The best batteries for outdoor cameras keep a trail camera, a doorbell camera, or a wire-free security camera running through cold nights and long gaps between visits. This guide covers six options verified from maker and retailer pages: an AA lithium cell, high-capacity rechargeable 16340 cells, and swappable packs made for Ring and Arlo cameras.
Quick verdict
For most outdoor cameras, the right battery is the one the camera maker lists for that model. The Tenergy RCR123A kit is the Arlo-certified pick for Arlo Wire-Free cameras, while the Orbtronic 16340 is the high-capacity rechargeable cell at 920mAh. The Energizer Ultimate Lithium AA is the pick for cameras that take AA cells.
The Arlo VMA5400 is the spare-pack pick for Arlo Ultra, Pro 3, Pro 4, and Pro 5S cameras, and the Ring Quick Release Ultra Battery Pack is the spare-pack pick for the newest Ring cameras at 10,000mAh. The Power Portable RCR123 kit is the bulk pick, with eight 700mAh cells and a four-slot charger for two full camera changes.
Check voltage before anything else. A 3.7 volt rechargeable 16340 cell is not a drop-in replacement for a 3 volt CR123A primary cell, and the wrong voltage can damage a camera made for 3 volt cells. Match the battery to the camera model, then pick the capacity and the charging plan.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| Energizer Ultimate Lithium AA | 1.5V AA lithium | Trail and AA cameras | 25-year storage, minus 40 to 140 degrees F | Single use, not rechargeable |
| Orbtronic 16340 RCR123A | 3.7V rechargeable Li-ion | Highest capacity 16340 cell | 920mAh, 3250mWh, Seiko protection | 3.7V only, not for 3V devices |
| Tenergy RCR123A 650mAh kit | 3.7V rechargeable Li-ion | Arlo Wire-Free cameras | Arlo certified, 4 cells plus USB charger | 650mAh, lowest capacity here |
| Power Portable RCR123 700mAh kit | 3.7V rechargeable Li-ion | Bulk 16340 supply | 8 cells at 700mAh, 4-slot smart charger | Charger holds 4 cells at a time |
| Arlo VMA5400 | 3.85V rechargeable Li-Po pack | Arlo Ultra and Pro cameras | 4800mAh, 18.48Wh, swap in seconds | Fits Arlo Ultra and Pro lines only |
| Ring Quick Release Ultra | Rechargeable Li-ion pack | Newest Ring cameras | 10,000mAh, USB-C fast charging | Not backward compatible with older Ring devices |
How we selected the best batteries for outdoor cameras
We picked batteries from maker and retailer pages that state voltage, capacity, size, and temperature range. Every battery here is listed on a page we opened, and every figure here comes from a page we opened. We left out any battery shown out of stock, and any battery that duplicates a cell from the earlier Arlo camera guide.
Voltage came first, because an outdoor camera takes either a 3 volt primary cell, a 3.7 volt rechargeable cell, or a maker pack built for that camera. A 16340 cell at 3.7 volts is not the same as a CR123A cell at 3 volts, and the camera manual decides which one fits. Capacity came next, since a wire-free camera that records motion all night needs more energy than a trail camera that wakes up a few times a day.
Fit and weather came last, since an outdoor battery works in cold nights, summer heat, and rain. We kept batteries with a stated temperature range, a stated size, and a clear list of compatible cameras. A swappable pack earns its place when a dead battery can be swapped in seconds instead of taking the camera down for a charge.
The best batteries for outdoor cameras
Six batteries cover outdoor cameras from a trail camera in the woods to a doorbell camera by the front door. One is a long-life AA lithium cell, three are rechargeable 16340 cells and kits, and two are swappable packs made for Ring and Arlo cameras. The sections below give the figures for each one so you can match the battery to the camera.
Energizer Ultimate Lithium AA
For a trail camera or a wire-free camera that runs on AA cells, this is the pick. The maker page lists a 1.5 volt AA cell with up to 25 years of storage life, an operating range of minus 40 degrees F to 140 degrees F, and a weight one-third less than a standard alkaline cell. It fits any camera that takes AA cells.
The maker describes this cell as its longest lasting AA in high-tech devices, and it is built for cameras that sit outside for weeks at a time. A trail camera that wakes up for motion a few times a day needs a cell that holds its charge in storage and still delivers full power on a cold morning. The wide temperature range covers winter nights and summer heat in one cell.
The light weight helps on a trail camera mounted high on a tree or a post, where every gram counts against the mount. The cell is a single-use lithium primary, so it is not rechargeable, and a spent cell is replaced rather than charged. Keep a spare set of AA cells with the camera so a dead cell never costs a week of photos.
- Up to 25 years of storage life
- Minus 40 to 140 degrees F operating range
- One-third lighter than standard alkaline
- Standard 1.5 volt AA size
- Single use, not rechargeable
- One cell per slot, so a multi-cell camera needs a full set
Buy it if your camera takes AA cells and sits outside for weeks. Skip it if your camera takes CR123A cells or a maker battery pack.
Orbtronic 16340 RCR123A
For a camera or flashlight that lists a 16340 or RCR123A 3.7 volt cell as compatible, this is the pick. The maker page lists a 3.7 volt protected lithium-ion cell at 920mAh and 3250mWh, with a charge current of 0.25 to 0.5 amps, a maximum discharge current of 3 amps, and a full charge voltage of 4.2 volts.
The cell measures 16.5 mm across and 34 mm long, weighs 0.63 oz, and carries a welded button top with integrated safety protection from Seiko in Japan. The maker raised the capacity from 880mAh to 920mAh, which is about 42 percent more rated capacity than a 650mAh cell and about 31 percent more than a 700mAh cell. A free battery safety case comes with quantities of two or more.
The limit is the voltage, and the maker states it plainly: this is not a replacement for a regular non-rechargeable 3.0 volt CR123A primary cell. Use it only where the device manual lists a 16340 or RCR123A 3.7 volt cell as compatible. Charge it fully to 4.2 volts before first use, on a charger made for lithium-ion cells, and store a spare cell in the case, not loose in a pocket.
- 920mAh, the highest capacity 16340 cell here
- Seiko protection circuit built in
- 3 amps maximum discharge current
- Free safety case with two or more cells
- 3.7 volts only, not for 3 volt devices
- Needs a lithium-ion charger, sold separately
Buy it if your device manual lists a 16340 or RCR123A 3.7 volt cell. Skip it if your camera takes 3 volt CR123A primary cells only.
Tenergy RCR123A 650mAh kit
For an Arlo Wire-Free camera, this is the pick. The kit pairs four Tenergy RCR123A batteries with a four-slot USB charger. Each cell is a 3.7 volt lithium-ion rechargeable at 650mAh, and Arlo certifies these cells for use in its wire-free cameras. The charger takes a 5 volt USB input from 500mA to 2000mA and delivers up to 400mA per slot.
An Arlo Wire-Free camera takes four CR123 lithium 3 volt photo batteries, and Arlo lists these Tenergy cells, marked Works with Arlo, as the rechargeable option for that camera. The four cells in the kit fill one camera, and the charger refills all four at once from a computer, a wall adapter, or a power bank. The charger measures 3.6 by 3.1 by 1 inch and weighs 92 grams, so it fits in a drawer or a travel bag.
The cells are built to be recharged hundreds of times, which cuts the stream of single-use cells a wire-free camera would otherwise eat through. The limit is capacity: at 650mAh these are the lowest-capacity rechargeable cells here, so a camera that records often will need its cells swapped sooner than a camera running the 920mAh Orbtronic cell. Keep a second set charged so the swap takes seconds.
- Arlo certified for Wire-Free cameras
- Four cells and a charger in one kit
- USB input works from a computer or power bank
- Rechargeable hundreds of times
- 650mAh, the lowest capacity here
- 3.7 volts, so it fits only cameras that accept rechargeable cells
Buy it if you run Arlo Wire-Free cameras and want the certified rechargeable set. Skip it if your camera takes 3 volt primary cells only.
Power Portable RCR123 700mAh kit
For a household with more than one camera that takes CR123A cells, this is the pick. The kit holds eight Power Portable RCR123 batteries at 3.7 volts and 700mAh each, plus a four-slot charger. The charger takes a 100 to 240 volt AC input, charges four cells at a time on independent channels, and uses constant current and constant voltage charging.
Eight cells cover two full changes for an Arlo Wire-Free camera, which takes four cells, or one change for two cameras. Each cell holds about 2.59 watt hours, so the eight cells together hold about 20.7 watt hours. The charger shows a red light while a cell charges, a green light when it is full, and a flashing red light for a short circuit or a cell placed the wrong way round.
The charger carries reverse polarity protection and a CE approval, and the maker names Tenergy as the charger maker and Power Portable as the battery maker. The cells carry no memory effect, so they can be recharged at any point without losing capacity. The limit is the four-slot charger: eight cells need two charging rounds, so charge the second set while the first set runs the camera.
- Eight 700mAh cells in one kit
- Four independent charging channels
- LED status for each slot
- Worldwide 100 to 240 volt charger input
- Charger holds four cells at a time, so eight cells need two rounds
- 3.7 volts, so it fits only cameras that accept rechargeable cells
Buy it if you run two or more cameras on CR123A cells and want spares ready. Skip it if you need one set only or your camera takes 3 volt primary cells.
Arlo VMA5400
For an Arlo Ultra, Ultra 2, Pro 3, Pro 4, or Pro 5S camera, this is the pick. The maker lists a 3.85 volt lithium polymer battery at 4800mAh and 18.48Wh for those cameras. The newest Ultra and Pro cameras use a 3.89 volt cell at 5505mAh and 21.41Wh, which Arlo also sells under the VMA5400 name, so check the label on the battery in the box.
A spare battery swaps into the camera in seconds, and the camera keeps recording while the spent battery charges. Charge the battery inside the camera housing with the magnetic charging cable, or charge it in the Arlo Dual Battery Charging Station, which is sold separately. The battery is the same one Arlo ships in the camera, so the fit and the contacts match without adapters.
The limit is the fit: this battery serves the Ultra and Pro 3, Pro 4, and Pro 5S lines, and Arlo lists a different 7.2 volt 2440mAh battery for the older Arlo Pro and Pro 2 cameras. Buy a second VMA5400 as the spare, and rotate the two batteries so one is always charged. A camera that records all night needs that spare more than a camera that wakes up a few times a day.
- 4800mAh and 18.48Wh in the standard cell
- Maker-original fit for five camera lines
- Swaps in seconds, no tools needed
- Charges in the camera or in a charging station
- Fits Arlo Ultra and Pro lines only
- Charging station sold separately
Buy it if you run Arlo Ultra or Pro cameras and want a charged spare ready. Skip it if your camera takes CR123A cells or a Ring pack.
Ring Quick Release Ultra Battery Pack
For the newest Ring cameras and doorbells, this is the pick. The maker lists a rechargeable lithium-ion pack at 10,000mAh with a USB-C port and built-in fast charging. Four LEDs on the pack show the charge level in 25 percent steps, and the pack measures 3.23 by 1.84 by 0.94 inches. It works from minus 5 degrees F to 120 degrees F.
The pack holds up to 67 percent more capacity than the standard Ring pack at 6040mAh, so it needs charging less often. It fits the Battery Doorbell Plus, Battery Doorbell Pro, Outdoor Cam, Spotlight Cam, and Peephole Cam 2K, in their newest models, and it works with the Ring Charging Station. A fast-charging claim on the page compares it with the standard pack charged without a fast charging station, so the gain depends on the charger used.
The limit is compatibility: this pack is not backward compatible with older Ring devices, so check the model list before buying. The pack is also larger than the standard pack, at 3.23 inches long against 2.75 inches for the standard pack. Keep a second pack charged and swap it in with the quick-release tab, and the camera never leaves the wall for a charge.
- 10,000mAh, the largest capacity here
- USB-C with built-in fast charging
- Four LEDs show charge in 25 percent steps
- Fits five newest Ring devices
- Not backward compatible with older Ring devices
- Larger than the standard Ring pack
Buy it if you run a newest-model Ring camera or doorbell and want the longest time between charges. Skip it if your Ring device is an older model.
Buying guide
An outdoor camera battery fails in three ways: the wrong voltage, the wrong size, or a charge plan that leaves the camera dark. The sections below walk through the checks that matter before you buy, from the voltage printed on the cell to the spare battery that keeps the camera on the wall.
Match the best batteries for outdoor cameras to your camera
Start with the camera manual, not the battery shelf. A trail camera takes AA cells, an Arlo Wire-Free camera takes four CR123A cells, an Arlo Ultra or Pro camera takes a VMA5400 pack, and a Ring camera takes a Quick Release pack. The manual lists the exact cell or pack, and that listing is the only match that counts.
Write down the camera model before you shop, and check the battery against that model on the maker page. A pack that fits the newest Ring doorbell will not fit an older Ring doorbell, and a VMA5400 will not fit an Arlo Pro 2. One minute with the model number saves a return and a week without a camera.
3 volts or 3.7 volts: the voltage check that protects your camera
A CR123A primary cell runs at 3 volts, and a rechargeable RCR123A or 16340 cell runs at 3.7 volts. The two cells share a size, but they do not share a voltage, and a camera built for 3 volt cells can be damaged by a 3.7 volt cell. Orbtronic states this on its page: its 16340 cell is not a replacement for a regular 3.0 volt CR123A primary cell.
Use a rechargeable 3.7 volt cell only where the camera manual lists a 16340 or RCR123A 3.7 volt cell as compatible. Arlo lists its Tenergy 650mAh cells, marked Works with Arlo, as the rechargeable option for its Wire-Free cameras. When the manual is silent, stay with the 3 volt primary cell the camera shipped with, and ask the maker before trying a rechargeable cell.
Cold nights and heat: what the temperature range means
An outdoor battery works in the coldest night and the hottest afternoon, and the temperature range on the page tells you how far it goes. The Energizer Ultimate Lithium AA lists minus 40 degrees F to 140 degrees F. The Ring Quick Release Ultra lists minus 5 degrees F to 120 degrees F, which covers most doorbell and garden cameras.
Capacity drops in the cold for every chemistry, so a camera that records all night in winter needs more headroom than the same camera in summer. A spare battery kept warm indoors and swapped in on a cold morning beats a battery that sat in the camera all night. Check the range on the page, then plan the swap around the coldest nights, not the mildest ones.
Rechargeable cells or swappable packs: plan the swap
A rechargeable cell saves money over hundreds of cycles, but it takes the camera down while it charges. A swappable pack costs more up front, but a charged spare swaps in within seconds and the camera never leaves the wall. Pick the plan that fits how often the camera records and how far it sits from a charger.
For CR123A cameras, buy two sets of cells and a charger that holds four at a time, so one set runs the camera while the other charges. For Arlo and Ring cameras, buy one spare pack per camera and rotate the two packs. Mark the spare with the date it was charged, and recharge it the same week it comes out of the camera.
Solar panels and charging stations: keep spares ready
A solar panel keeps a spare battery ready without taking the camera down. Arlo sells a Dual Battery Charging Station that charges a VMA5400 off the camera, and Ring sells a Charging Station that takes its Quick Release packs. A panel on the camera trickles charge into the pack during the day, which stretches the time between swaps.
Match the station to the battery, not just to the brand. The Arlo station takes Arlo packs, the Ring station takes Ring packs, and a CR123A charger takes 16340 cells only when the charger lists that size. A station that charges the spare while the camera runs is worth more than a fast charger that needs the camera on a bench.
FAQ
Outdoor camera batteries raise the same questions again and again: which voltage fits, how many cells a camera takes, and how long a pack lasts. The answers below come from the maker pages listed in the sources, and each one points back to the camera manual as the final word.
Can I use rechargeable RCR123A cells in a camera made for CR123A
Only when the camera manual lists a 16340 or RCR123A 3.7 volt cell as compatible. A CR123A primary cell runs at 3 volts, and a rechargeable RCR123A cell runs at 3.7 volts, so the rechargeable cell can damage a camera built for 3 volt cells. Orbtronic states on its page that its 16340 cell is not a replacement for a 3.0 volt CR123A primary cell.
Arlo is the clear case for a rechargeable swap: Arlo lists Tenergy 650mAh cells marked Works with Arlo as the rechargeable option for its Wire-Free cameras. For any other camera, check the manual first, and stay with the 3 volt primary cell when the manual does not list a rechargeable cell.
How many CR123A batteries does an Arlo Wire-Free camera take
An Arlo Wire-Free camera takes four CR123 lithium 3 volt photo batteries. Arlo states this on its support page, and it lists Tenergy RCR123A 650mAh cells marked Works with Arlo as the rechargeable option. The Tenergy kit in this guide holds four cells, which fills one camera, and the Power Portable kit holds eight cells, which fills two cameras.
Change all four cells at once, and do not mix a fresh cell with a spent one or a rechargeable cell with a primary cell. A camera that takes four cells draws from all four, and one weak cell shortens the run for the whole set. Keep the four cells of a set together, and charge or replace them as a set.
How long does a Ring battery pack last between charges
Ring states that battery life varies with device usage, settings, and environmental factors such as temperature and the number of motion events or live views. The 10,000mAh Ultra pack holds up to 67 percent more capacity than the standard 6,040mAh pack, so it runs longer between charges on the same camera.
Cut the motion load to stretch the pack: narrow the motion zones, lower the sensitivity, and shorten the recording length where the app allows it. Cold nights shorten the run, so check the pack in the app when the temperature drops, and swap in the charged spare before the camera goes dark.
Do AA lithium batteries work in trail cameras in winter
Yes, and the temperature range is the reason. The Energizer Ultimate Lithium AA lists an operating range of minus 40 degrees F to 140 degrees F, which covers a winter night in the woods and a summer afternoon on a fence post. The maker also lists up to 25 years of storage life, so a set bought in autumn still holds its charge in spring.
A trail camera that wakes up a few times a day draws little power, so the AA lithium cell lasts for months in that use. Check the camera after the first cold snap, and carry a spare set of AA cells on the visit so a dead set never costs a week of photos.
Can I charge a Ring battery pack with any USB-C cable
The Ring Quick Release Ultra Battery Pack charges through its USB-C port. Connect it to a standard USB-C cable and a power source, with no extra accessories needed. Four LEDs on the pack show the charge level in 25 percent steps while it charges, and the Ring app shows battery health under Device Health.
Use a power source that can deliver the current the pack wants, and charge the pack indoors on a cold day, since the pack lists an operating range down to minus 5 degrees F. A spare pack on the charger while the camera runs on the other pack keeps the camera on the wall without a gap.
Conclusion
Match the battery to the camera first, then pick capacity and a charging plan that keeps a spare ready. The Tenergy kit covers Arlo Wire-Free cameras, the Orbtronic cell covers 16340 devices, and the Arlo and Ring packs cover their own cameras with a swap that takes seconds. Check the voltage before you buy, and keep a charged spare on the shelf.
Write Your Review
No reviews yet. Be the first to share your experience!