Best batteries for small electric car conversion builds are 12V 100Ah LiFePO4 units wired in series, because four of them form a 48V string with about 5.1 kWh of energy. This guide compares six such batteries on current ratings, cycle life, cold-weather charging, weight, and warranty, and it flags the one model that cannot wire in series at all.

Small electric car conversion batteries at a glance

All six batteries below are 12V 100Ah LiFePO4 units, so each one stores about 1.28 kWh on its own. The differences that matter for a conversion are series wiring, continuous current, cold-weather charging, weight, and warranty length, and one of the six cannot wire in series at all.

Battle Born BB10012i Smart 100Ah 12V

The Battle Born 100Ah 12V Smart battery is the reference unit in this group, with Bluetooth monitoring, a 10-year warranty, and series wiring to 48V. It fits Group 27 and Group 31 trays, which covers most conversion battery boxes, and it carries the strongest certifications in this guide.

The maker page lists a 3,000 to 5,000 cycle lifespan, a 10-year warranty, and an IP65 rating for dust and water resistance. The cells carry UL 1642 recognition, the pack is ETL listed to UL 2054 and UL 62133-2, and the battery holds UN 38.3 transport certification. Assembly takes place in Reno, Nevada, and the maker page shows the unit in stock. Flexible mounting orientation lets the pack sit in any direction, which helps in tight conversion bays where a fixed upright case would not fit.

Series wiring is the point that matters most here. The maker page states that these batteries wire in series to build 24V, 36V, or 48V configurations, and that parallel connections are unlimited within the installation guidelines. That makes the Smart 100Ah unit a direct building block for a 48V low-speed conversion, with four units forming the string. One gap in the opened page is worth noting: the maker page lists no continuous discharge figure in its text, so the controller should be sized from the maker datasheet rather than from this guide alone.

LiTime 12V 100Ah LiFePO4

The LiTime 12V 100Ah battery is the lightest widely stocked option here at 24.25 lbs, with 4,000-plus cycles at full depth of discharge and a 100A continuous rating. It wires in series up to 48V, which suits a low-speed conversion, and its Group 31 case drops into trays built for lead-acid units.

Each unit holds 1,280Wh and delivers 1,280W of output power, and the maker rates the cells for 4,000-plus cycles at 100 percent depth of discharge with a lifetime of more than 10 years. The maker page lists a 3 percent self-discharge rate, full BMS protection, and IEC 62619 compliance. Charging runs from 32 to 122 degrees F and discharge from minus 4 to 140 degrees F. The maker states plainly that this model has no low-temperature protection, so it should only charge when the battery temperature is above 32 degrees F. On cold days the maker advises bringing the battery indoors to charge, and it points buyers who need sub-zero charging toward its cold-weather models.

Connection rules are spelled out on the maker page. Up to four units connect in series for 24V, 36V, or 48V, up to four connect in parallel for 400Ah, and a series-parallel bank can reach 16 units in a 4S4P layout. Every battery in a connected bank must be the identical model from the same brand, bought close together, with voltages balanced to within 0.1V before connecting. The maker also states that these batteries are for energy storage, not starting, and that a LiFePO4 charger or a DC-to-DC charger is the right way to charge them. Recommended charging voltage is 14.2V to 14.6V, with a 20A charge taking around five hours and a 50A charge taking around two hours to about 97 percent.

Renogy 12V 100Ah Pro Smart

The Renogy 12V 100Ah Pro Smart battery adds self-heating and Bluetooth to the 100Ah class, with a 245A peak rating for 30 seconds and a 7-year warranty. Its hard limit is wiring: it connects in parallel only, never in series, so it cannot build a 48V string for a conversion.

The maker page lists a 100A maximum charge current and a 100A maximum discharge current, with a 245A peak for 30 seconds that can support heavy loads such as air conditioners. Cycle life is rated at 5,000 cycles at 80 percent depth of discharge. The self-heating function switches on automatically when the battery temperature drops below 41 degrees F and a charging current above 4A is present, and it stops once the temperature passes 50 degrees F. Charging runs from minus 4 to 131 degrees F and discharge from minus 4 to 140 degrees F. The case carries an IP67 rating and a UL94 V-0 flame-retardant rating, the unit measures 10.6 by 7.6 by 8.1 inches, and it weighs 26.9 lbs.

Bluetooth connects the battery to the Renogy app for monitoring and over-the-air updates, and the unit also works with Renogy ONE monitors. The maker describes a double active protection system built around more than 60 BMS protection mechanisms plus an active backup protection layer that cuts the circuit far faster than passive protection when a MOSFET switch fails. The maker FAQ states the limit in plain terms: Pro Series batteries can only connect in parallel, up to eight units for 10.24 kWh at 12V, and never in series. That rules this battery out for any conversion that needs 24V or more, no matter how strong its peak rating looks.

Three more 12V 100Ah units for an EV build

The next three units cover the budget end, the golf-cart footprint, and the weatherproof end of the 100Ah class. Two of them wire in series to 48V, and the third brings Bluetooth and an IP67 case at a lower weight than most of the field. The Epoch is the lightest, the BBGC2 fits golf-cart trays, and the DC HOUSE is the weatherproof pick.

Epoch 12V 100Ah Eco Series

The Epoch 12V 100Ah Eco Series is the lightest battery in this guide at 21 lbs, in a Group 24 case, with a 300A peak rating for five seconds. It trades Bluetooth and heating for a 4,500-plus cycle rating and a 6-year warranty, which suits warm-climate builds in this group.

The listing page gives the full specification set: 100Ah at 12.8V for 1.28 kWh, 100A maximum continuous discharge and charge, 300A peak discharge for five seconds, and a 4,500-plus cycle life. Series wiring runs up to four units for 48V, and parallel wiring runs up to 16 units for 20.48 kWh at 12V. The case measures 10.25 by 6.75 by 9.00 inches and carries an IP54 rating. Charging needs 32 to 131 degrees F because the Eco Series has no internal heating, while discharge runs from minus 4 to 140 degrees F. Cells carry UL 1642 and UL 9540A recognition plus IEC 62619:2022, CE, and RoHS marks. The listing page shows the battery in stock at an authorized dealer.

The listing page is candid about what the Eco Series leaves out. There is no Bluetooth and no internal heating, so state of charge must be read from a charge controller, an inverter, or a shunt-based monitor, and charging below freezing is not possible. The page also notes that for 36V or 48V banks, purpose-built single-case batteries avoid the balance issues that come with series strings, so that comparison is worth making before committing to four separate units. For a warm-climate 48V build where weight matters, the 21 lb case and the 300A peak rating are the strongest points in this group.

Battle Born BBGC2 100Ah GC2

The Battle Born BBGC2 packs 100Ah into a GC2 golf-cart footprint, so it drops into trays built for pairs of 6V GC2 lead-acid batteries. It wires in series to 48V and carries the same 10-year warranty as the Smart 100Ah unit, with a Class 1 Division 2 rating for hazardous locations.

The maker manual lists a 100A maximum discharge current, a 200A peak for 30 seconds, and a half-second surge rating for loads above 200A. Cycle life runs 3,000 to 5,000 cycles at 100 percent depth of discharge, efficiency is listed at 99 percent, and self-discharge runs 2 to 3 percent per month. Maximum charge current is 50A, with absorption at 14.2V to 14.6V and float at 13.4V to 13.8V. Operating temperature runs minus 4 to 135 degrees F, charging runs 25 to 135 degrees F, and storage runs minus 10 to 140 degrees F. The unit measures 10.31 by 7.28 by 11.02 inches and weighs 31 lbs, with flag-style terminals that take a 3/8 inch or 5/16 inch bolt. The maker page shows the unit in stock.

The GC2 footprint is the reason this battery earns a place here. Many small conversions start from golf-cart donor platforms, and those trays hold pairs of 6V GC2 batteries wired for 12V. One BBGC2 replaces such a pair with a single 12V unit, and four of them wire in series to 48V. The manual also covers a heated variant, the BBGC2H, for builds that charge in freezing weather. Certifications include ETL listing to UL 2054 and UL 62133-2, UN 38.3, UL 1642 cells, an IP65 rating, and Class 1 Division 2 approval for the non-heated model. The trade-off is weight: at 31 lbs this is the heaviest unit in the guide, so a four-unit string weighs 124 lbs.

DC HOUSE 12V 100Ah IP67

The DC HOUSE 12V 100Ah battery pairs an IP67 case with Bluetooth 5.1 and a fault buzzer, at 22.6 lbs in a Group 27 case. It wires in series up to four units, and its low-temperature cutoffs sit lower than the unheated models here. A 3-year warranty backs the unit, and the maker lists up to 15,000 cycles.

The maker page lists 12.8V, 100Ah, and 1,280Wh, with a 100A maximum continuous charge and discharge current and a 120A peak for 10 seconds. Series and parallel connections run to four units each, in layouts up to 4S4P. The case measures 12.1 by 6.7 by 8.5 inches and the specification table lists 22.6 lbs. Charging runs 32 to 131 degrees F and discharge runs minus 4 to 131 degrees F. When the BMS senses temperatures below 19.4 degrees F, charging cuts off, and when temperatures drop below minus 4 degrees F, discharging also cuts off. Charging resumes automatically at 32 degrees F and above. Bluetooth 5.1 reaches up to 66 feet and pairs with the maker app to show state of charge, voltage, and current.

The maker lists a 3-year warranty alongside a 10-year lifespan and up to 15,000 cycles. That cycle figure stands far above every other battery in this guide, so it should be read as the maker claim it is rather than as a point of direct comparison. An internal metal compression fixture holds the four-cell structure, the casing is flame-retardant and self-extinguishes within 30 seconds, and a fault buzzer sounds in a repeating pattern of two seconds on and eight seconds off when the BMS detects a fault. Terminals are M8 bolts. The maker page shows the unit in stock.

How to choose a battery for a small electric car conversion

Choosing starts with the voltage of the motor and controller, then moves to current, climate, and weight. A battery that is strong on one of those points can still be wrong for a build if it fails another, so check all four before ordering a full string.

Match the voltage with series wiring

Most small conversions run on 48V, which takes four 12V units in series. Five of the six batteries here allow that; the Renogy Pro does not, so it can only serve a 12V system despite its strong peak rating and self-heating. Check the series limit on the maker page before buying the string.

Four 12.8V units in series give a nominal 51.2V string, and the maker series limits in this guide all stop at 48V. A build that needs 72V or 96V therefore needs purpose-built higher-voltage packs rather than more 12V units. Wiring rules matter as much as voltage: use the identical model from the same brand, buy the units close together, and balance their voltages to within 0.1V before connecting. The Battle Born manual also states that batteries must not run in series or parallel with any other type of battery. A 24V build needs two units in series and a 36V build needs three, with the same matching rules applying each time.

Check the continuous current rating

Five of the six batteries list a 100A continuous discharge rating, which sets the ceiling for motor current. Peak ratings differ widely, from 120A for 10 seconds on the DC HOUSE to 300A for five seconds on the Epoch, so size the controller to the continuous figure.

At 51.2V and 100A, a 48V string delivers about 5.1 kW of continuous power, which frames the motor size a four-unit string can feed. Peak figures cover short bursts such as startup surge: the Epoch lists 300A for five seconds, the Renogy lists 245A for 30 seconds, the BBGC2 lists 200A for 30 seconds, and the DC HOUSE lists 120A for 10 seconds. The LiTime page lists a 100A continuous rating and states no peak figure, while the Battle Born Smart page lists no continuous figure at all. Size the controller to the continuous rating, not to the peak, because the peak only lasts seconds and the continuous rating governs sustained driving.

Plan for cold-weather charging

LiFePO4 cells cannot take a charge below freezing unless the battery heats itself or the BMS blocks charging. The Renogy Pro heats itself below 41 degrees F, while the LiTime and Epoch models simply need temperatures above 32 degrees F to charge, so plan around the climate.

The Renogy Pro is the only unit here with built-in heating: it warms itself when the temperature drops below 41 degrees F and a charging current above 4A is present, and it keeps charging down to minus 4 degrees F. The DC HOUSE takes a different approach with cutoffs: charging stops below 19.4 degrees F and discharging stops below minus 4 degrees F, with charging resuming at 32 degrees F. The BBGC2 charges from 25 degrees F upward with a BMS low-temperature cutoff, and its manual covers a heated BBGC2H variant for colder builds. The LiTime and Epoch models have no heating and no cutoff beyond the standard BMS, so they need temperatures above 32 degrees F to charge. For storage, the LiTime page advises keeping the battery at 50 percent state of charge and recharging to that level at least every three months.

Sizing a pack for a small electric car conversion

Pack size follows from voltage first and energy second. Once the string voltage matches the motor, the number of parallel strings sets range, and the weight of the whole bank sets what the chassis must carry, so size both together. Four units give about 5.1 kWh, and eight give about 10.2 kWh.

How much energy does a 48V string hold

Four 100Ah units in series hold about 5.1 kWh, because series wiring adds voltage while capacity stays at 100Ah. A second parallel string doubles that to about 10.2 kWh, at the cost of four more batteries and their weight, so plan the tray for the full bank.

Each unit in this guide stores about 1.28 kWh, so the math stays simple: one unit gives 1.28 kWh at 12V, four in series give about 5.12 kWh at 48V, and eight in a 4S2P layout give about 10.24 kWh. Weight adds up just as directly. A four-unit string weighs 84 lbs with the Epoch, about 90 lbs with the DC HOUSE, 97 lbs with the LiTime, and 124 lbs with the BBGC2. Range depends on vehicle weight, motor size, terrain, and driving style, so no single miles figure applies to every build. Treat any range claim that ignores those factors with care, and size the pack with headroom rather than to the exact edge of the trip.

Charging a series string

A series string needs a charger matched to the full string voltage, with a LiFePO4 profile. Lead-acid charger voltages are wrong for these cells, and the Epoch listing page notes that mismatch either undercharges the pack or shortens its life, so budget for the right charger.

Per-unit absorption voltage runs 14.2V to 14.6V on both the LiTime and BBGC2 pages, which works out to about 57 to 58V for a four-unit 48V string. The BBGC2 manual adds a float voltage of 13.4V to 13.8V and notes that temperature compensation should stay disabled. Charge times for a single LiTime unit run around five hours at 20A and around two hours at 50A to about 97 percent. Before connecting units in series, balance their voltages to within 0.1V so no large inrush current flows between them. For solar charging, the LiTime page states that 400W of panels can fully charge one unit in a day with 4.5 hours of effective sunshine, which gives a sense of scale for a solar-fed conversion.

What to watch before you buy

Three details catch buyers out: a battery that cannot wire in series, a charger with the wrong profile, and a tray that does not fit the case. Each one is cheap to check before ordering and costly to fix after the pack arrives, so run through all three first.

The Renogy Pro cannot wire in series

The Renogy Pro is the only battery here with self-heating and a 245A peak rating, yet it connects in parallel only. That makes it a strong 12V auxiliary battery and a poor choice for any conversion that needs 24V or more, no matter how strong the numbers look.

Up to eight Pro units can join in parallel for 10.24 kWh at 12V, which suits a large 12V house bank or a 12V low-speed build. It does not suit a 48V traction pack at any quantity, because the maker FAQ bars series wiring outright. Buyers who need both heating and 48V should look at the BBGC2H heated variant in the Battle Born manual, or at a purpose-built higher-voltage pack, rather than trying to force the Pro into a string it was never built for.

Lead-acid chargers and LiFePO4 profiles

A charger built for lead-acid uses voltages that do not suit LiFePO4 cells. The Epoch listing page states plainly that the wrong profile either undercharges the pack or shortens its life, so budget for a lithium-profile charger before the build starts, not after.

The correct absorption range for the units in this guide is 14.2V to 14.6V per 12V battery, with the BBGC2 manual adding a float range of 13.4V to 13.8V and an equalization voltage of 14.4V where applicable. A DC-to-DC charger works for alternator charging, and a solar charge controller needs LiFePO4 settings as well. For storage between builds, keep the battery near 50 percent state of charge and recharge to that level at least every three months, following the LiTime page guidance. A charger is part of the conversion budget, not an afterthought, and the wrong one can quietly cut years off a new pack.

Weight, tray fit, and mounting

Group sizes differ across this guide: the Epoch is Group 24, the DC HOUSE is Group 27, the LiTime replaces Group 31, and the BBGC2 uses the GC2 golf-cart footprint. Measure the tray and the cable runs before ordering, not after the batteries arrive in the shop.

Dimensions make the differences concrete. The Epoch measures 10.25 by 6.75 by 9.00 inches, the Renogy Pro measures 10.6 by 7.6 by 8.1 inches, the DC HOUSE measures 12.1 by 6.7 by 8.5 inches, and the BBGC2 measures 10.31 by 7.28 by 11.02 inches. The BBGC2 uses flag-style terminals with a 3/8 inch hole, while the Renogy Pro and DC HOUSE use M8 bolts. Battle Born allows flexible mounting orientation, which helps when a tray is shallow or oddly shaped. The Renogy page also advises leaving 1.97 to 3.94 inches of clearance above the battery and at least 7.87 inches on the busbar side, which is a useful check for any tight conversion bay.

Frequently asked questions

The questions below cover the three points buyers ask about most: how many batteries a conversion needs, whether brands can mix in one string, and whether cold weather forces a heated battery. Each answer follows the figures on the maker and dealer pages.

How many batteries does a small electric car conversion need

A 48V conversion needs four 12V units in series, a 24V conversion needs two, and a 12V auxiliary bank needs one. Four units give about 5.1 kWh, and a second parallel string doubles the energy and the weight of the bank. Count the string first, then decide on a second string for range.

Three units in series give 36V for builds that run on that voltage, and the same matching rules apply at every voltage: identical model, same brand, bought close together, voltages balanced within 0.1V. The Renogy Pro is the exception to every count above, because it cannot wire in series at any voltage. Count the string first, then decide whether a parallel string is needed for range, and only then check that the tray and the chassis can carry the total weight.

Can I mix battery brands in one string

No. The LiTime page states that every battery in a connected bank must be the identical model from the same brand, bought close together, with voltages balanced within 0.1V. The Battle Born manual also bars mixing battery types in series or parallel.

Different brands use different BMS designs, different internal resistance, and different cell behavior, so a mixed string drifts out of balance and ages unevenly. The practical rule is simple: buy the full string at once, from one maker, in one order, and check the voltage of each unit before the first connection. A single mismatched unit can drag down the whole string, and the fix is a replacement, not a rebalance.

For a 48V electric car conversion, the Battle Born BB10012i and BBGC2 lead on warranty and series flexibility, the Epoch Eco leads on weight, and the LiTime leads on cycle life at full depth of discharge. The Renogy Pro fits only 12V systems, and the DC HOUSE fits builds that face wet and cold use. Pick voltage first, then current, then climate.

Related guides

Browse all Buying Guides guides →