A halogen headlight spreads light in a wide, soft cone, while a projector lens focuses it into a sharp beam with a clean cutoff. The best HID projectors for retrofit use a bi-xenon lens, a curved cutoff shield, and a matched ballast and bulb, so low beam stays low and high beam reaches far down the road.
Quick verdict
For most retrofit jobs, a 2.5-inch bi-xenon projector with a 35 W HID kit is the right starting point, because it fits the most housings and needs the least cutting. The five picks below cover tight housings, wide beams, and complete kits, so a first-time builder and a seasoned installer can both find a match.
| Product | Bulb type | Lens size | Best for | Main limit |
|---|---|---|---|---|
| Morimoto Mini H1 9.0 | H1 HID | 2.5 inches | Tight housings | 35 W HID systems only |
| RWR Mini D2S 4.0 | D2S HID | 3.0 inches | Widest beam | Needs a HID conversion kit to light |
| RWR H1 8.0 | H1 HID | 2.5 inches | Sharp ECE cutoff | Needs a HID conversion kit to light |
| Morimoto Mini H1 Stage III | H1 HID | 2.5 inches | Complete kits | Page text still describes an older generation |
| ACME H1 Standard System | H1 HID | 2.5 inches | Budget builds | Based on older Morimoto designs |
How we selected
Lens size, bulb type, housing depth, and kit contents decide this guide, since an HID retrofit projector must fit common headlight housings, use a clear lens with a sharp cutoff, and pair with a 35 W HID ballast and bulb. The five picks below were weighed on those terms, with fit first.
Lens size leads the list. A 2.5-inch lens fits the most housings with the least cutting, while a 3.0-inch lens suits larger housings and gives a wider beam. Housing depth matters as much as lens size, because the projector body must clear the back of the housing, so the guide lists the minimum depth where the maker states it.
Bulb and ballast matching comes next. The picks here use H1 or D2S HID bulbs with 35 W ballasts, and the guide states which bulb each projector takes, since an H1 bulb will not fit a D2S projector and a D2S bulb will not fit an H1 projector. Complete kits that include ballasts, bulbs, and a harness save a buyer from matching parts one by one.
Beam pattern and cutoff round out the shortlist. A curved cutoff shield gives a sharp low beam line that keeps glare out of oncoming eyes, while a bi-xenon solenoid flips the shield for high beam. The guide notes the beam pattern each maker lists, such as LHD or an ECE sloped pattern, so a buyer can match the projector to the side of the road they drive on.
Kit completeness is the last filter. A complete kit that includes ballasts, bulbs, a harness, and shrouds saves a first-time builder from matching parts across sellers, while a standalone projector suits a builder who already owns ballasts and bulbs from an earlier job. The guide keeps both types, but it states plainly which picks need extra parts and which ones arrive ready to wire. A buyer who starts with a complete kit can still swap the shroud or the bulb color later, since the projector, ballast, and harness stay the same. A builder who already owns a ballast and bulb set from an earlier job can save by buying a standalone projector, since the lens is the only new part the job needs.
The five best HID projectors for retrofit
These five models cover the main retrofit jobs, from a tight housing that needs a compact lens to a full kit with ballasts, bulbs, and a harness. Each entry gives the key facts, the job it fits best, and the limits a buyer should weigh before choosing.
Morimoto Mini H1 9.0
The Morimoto Mini H1 9.0 is the most compact pick in this guide, with a 2.5-inch lens, a 20 mm mounting shaft, and a minimum housing depth of 115 mm, so it fits housings that a larger projector cannot enter. It takes H1 HID bulbs only and runs on 35 W HID systems only, with an AR-coated Kuria Optic borosilicate glass lens that keeps the beam clear.
The projector fits H4 and H7 housings directly, and the kit includes H4 and H7 grommets and adapter plates, a MotoHolder clip and lock ring, and a high-beam solenoid pigtail. The maker lists a three-year warranty on the page. The listing page shows the model in stock. Note that this projector needs a separate HID ballast and bulb kit to light, since the listing covers the projector unit itself.
Pros
- 2.5-inch lens with only 115 mm minimum housing depth
- AR-coated Kuria Optic borosilicate glass lens
- Direct fit for H4 and H7 housings with grommets included
- MotoHolder clip and lock ring in the kit
- Three-year warranty listed on the page
Cons
- 35 W HID systems only, no LED option listed
- Ballast and bulbs sold separately
Buy it if your housing is tight and you want the most compact quality projector in this guide. Skip it if you want a complete kit with ballasts and bulbs in one box.
RWR Mini D2S 4.0
The RWR Mini D2S 4.0 is the widest-beam pick in this guide, with a 3.0-inch lens, D2S bulbs, and a curved cutoff shield that the seller describes as giving a sharp low beam line. A Kuria Optic clear lens sits in front of the optics, and a longer threaded shaft makes the install easier, with threads the seller describes as hard to strip.
The bi-xenon solenoid plugs into the back of the projector, with almost no slack in the mechanism per the listing. The seller states that the projector is so bright it exceeds the maximum amount of intensity allowed by DOT even at 35 W; that is the seller’s claim, not a measured figure from this guide, and a buyer should aim the beam with care. The projector needs an HID conversion kit to light, and LED bulbs will work but perform worse than a HID kit per the seller. The listing page shows the model in stock.
Pros
- 3.0-inch lens for a wide beam
- D2S bulbs with a curved cutoff shield
- Kuria Optic clear lens
- Longer threaded shaft for easier install
- Solenoid plugs into the back of the projector
Cons
- Needs an HID conversion kit to light
- 3.0-inch lens needs a larger housing than 2.5-inch models
Buy it if your housing has room for a 3.0-inch lens and you want the widest beam in this guide. Skip it if your housing is tight or you want a complete kit in one box.
RWR H1 8.0
The RWR H1 8.0 is a 2.5-inch bi-xenon projector with a blue AR clear lens and an ECE sloped beam pattern, which suits drivers who want a sharp cutoff with a stepped edge for the roadside. MotoHolder precision bulb holders come standard, and a blue anodized lock ring holds the projector in place.
The projector fits Mini Gatling Gun and Mini Graphite shrouds, and full-size shrouds fit with centric rings, so a builder can dress the lens to match the housing. Like the other standalone projectors in this guide, it needs an HID conversion kit to light. The listing page shows the model in stock.
Pros
- 2.5-inch lens with a blue AR clear lens
- ECE sloped beam pattern
- MotoHolder precision bulb holders standard
- Blue anodized lock ring included
- Fits Mini Gatling Gun and Mini Graphite shrouds
Cons
- Needs an HID conversion kit to light
- Full-size shrouds need centric rings
Buy it if you want a sharp ECE cutoff in a compact 2.5-inch body. Skip it if you want a complete kit with ballasts and bulbs included.
Morimoto Mini H1 Stage III
The Morimoto Mini H1 Stage III is a complete kit that pairs two Morimoto H1 9.0 LHD projectors with 35 W Morimoto XB ballasts, H1 XB bulbs in 5500K or 6500K, Mini H1 MotoHolders, and a relay wire harness. A buyer picks a shroud from Apollo 1.0, Bullet, Gatlin Gun 2.0, or Mini Turbine, so the kit covers the lens trim as well as the light source.
The kit suits a first-time builder because it matches every part in one box: the projectors, the holders, the ballasts, the bulbs, and the harness all come from the same maker. Note that the descriptive text on the page still describes the older Mini H1 7.0 generation, while the spec table lists H1 9.0 projectors; this guide uses the spec-table figure of H1 9.0. The listing page shows the kit in stock.
Pros
- Complete kit with projectors, ballasts, bulbs, and harness
- H1 9.0 LHD projectors per the spec table
- 35 W Morimoto XB ballasts with H1 XB bulbs
- Shroud choice from four styles
- Mini H1 MotoHolders included
Cons
- Page text still describes an older generation
- Bulb choice limited to 5500K or 6500K
Buy it if you want a complete, matched kit with no part matching to do. Skip it if you want to pick each part yourself or need a different bulb color.
ACME H1 Standard Projector System
The ACME H1 Standard Projector System is the budget kit in this guide, with a clear lens and a curved cutoff shield that produce a wide, bright, and respectably sharp beam pattern per the listing. The projectors are based on older Morimoto designs, so a buyer who wants the latest optics should look at the Morimoto picks above instead.
The kit includes 35 W ACME SpeedyStart ballasts that reach full intensity in 3.5 seconds, ACME H1 bulbs in 5000K, 6000K, or 8000K, and a Morimoto relay wire harness with triple-sealed central relay packs and 14-gauge stranded copper wiring. Shroud choices cover Apollo 1.0, Bullet, Gatlin Gun 2.0, and Mini Turbine. Optional extras include MotoHo1der precision bulb holders, Canbus harnesses for cars that watch for bulb-out warnings, and butyl housing sealant. The listing page shows the kit in stock.
Pros
- Clear lens with a curved cutoff shield
- 35 W ballasts reach full intensity in 3.5 seconds
- Bulb choice in 5000K, 6000K, or 8000K
- Morimoto relay harness included
- Four shroud styles to choose from
Cons
- Based on older Morimoto designs
- Precision bulb holders and Canbus harness cost extra
Buy it if your budget is tight and you want a complete kit with a strong harness. Skip it if you want the latest projector optics.
Buying guide
Choosing a retrofit projector means matching lens size, bulb type, and housing depth to the headlight, not chasing the brightest claim on a listing. The points below use the facts from the product pages in this guide, so a buyer can weigh each model on the same terms.
Lens size for HID projectors for retrofit
Lens size decides how much cutting the housing needs. A 2.5-inch lens fits the most housings with the least cutting, while a 3.0-inch lens needs a larger opening and suits bigger housings. Measure the reflector bowl and the space behind it before buying, and check the minimum housing depth the maker lists.
Depth matters as much as diameter. The Mini H1 9.0 lists a minimum housing depth of 115 mm, and a projector that is too deep will hit the back of the housing or the bulb cap. The RWR Mini D2S 4.0 uses a longer threaded shaft, which helps the install but still needs room behind the reflector.
Bulb and ballast matching
Bulb type must match the projector. The H1 picks in this guide take H1 HID bulbs only, while the D2S pick takes D2S bulbs only, and the two types do not swap. Ballast wattage must match too: all five picks run on 35 W HID systems, and a 55 W ballast would overdrive the bulb and shorten its life.
Complete kits remove the guesswork. The Stage III kit and the ACME kit both include matched ballasts, bulbs, and a harness, so a first-time builder does not need to match parts one by one. Standalone projectors cost less but need a separate HID conversion kit to light.
Beam pattern and cutoff
Beam pattern decides where the light lands. A curved cutoff shield gives a sharp low beam line that keeps glare out of oncoming eyes, while a bi-xenon solenoid flips the shield for high beam. The RWR H1 8.0 lists an ECE sloped beam pattern, which steps up on the roadside for sign lighting.
Drive side matters. The picks in this guide list LHD beam patterns, which suit roads where traffic drives on the right. A projector made for the other side will throw light into oncoming traffic, so check the pattern before buying and aim the beam after the install.
Shrouds and sealing
Shrouds cover the projector after install and restore a factory-finished look inside the housing. The picks here fit Mini Gatling Gun, Mini Graphite, Apollo 1.0, Bullet, Gatlin Gun 2.0, and Mini Turbine shrouds, and full-size shrouds fit the RWR H1 8.0 with centric rings. Pick a shroud that covers the lens edge without blocking the beam.
Sealing keeps moisture out of the housing. Butyl sealant, listed as an option with the ACME kit, restores the factory seal when the lens goes back on. A housing that fogs after a retrofit usually has a weak seal, so take time on this step and test the seal before the first rain.
Legality and aiming
Retrofit headlights must meet local rules, which vary by state and country. A sharp cutoff and correct aim help, but a retrofit does not carry the same approval as a factory headlight, so check local rules before driving with the new lights and keep the stock headlights until the retrofit passes any needed check.
Aiming matters as much as the projector itself. A well-aimed beam lights the road without blinding oncoming drivers, while a poorly aimed beam wastes the projector and draws attention. Aim the lights on a flat surface against a wall, set the cutoff at the height the car maker lists, and recheck the aim after the first drive. A garage door or a flat wall at night gives a clear view of the cutoff line, and a tape measure on the wall marks the height to aim for.
FAQ
These answers cover the questions drivers ask most often when they shop for a retrofit projector, from lens size and bulb type to beam pattern, sealing, and setup. Each answer uses the facts from the picks above, plus general buying knowledge where a product page states no figure.
What is a retrofit projector?
A retrofit projector is a lens unit that fits inside a stock halogen headlight housing, replacing the reflector bowl with a focused lens and a cutoff shield. It takes an HID bulb and ballast, focuses the light into a sharp beam, and gives low beam and high beam from one lens through a bi-xenon solenoid.
The install needs the headlight opened, the reflector cut or drilled, the projector mounted on a threaded shaft, and the lens resealed. It is a hands-on job that takes several hours, so a first-time builder should read the install guide for the exact model before starting.
Are HID projectors for retrofit street legal?
It depends on local rules, which vary by state and country. A retrofit projector with a sharp cutoff and correct aim is far less glaring than a bare HID bulb in a halogen reflector, but it does not carry the same approval as a factory headlight. Check local rules before driving with the new lights.
Aim and bulb color affect the outcome. A correctly aimed beam with a 5000K or 5500K bulb looks close to factory HID light, while a high-mounted beam or a blue 8000K bulb draws more attention. Keep the stock headlights until the retrofit is checked and aimed.
Do I need ballasts for HID projectors?
Yes. An HID bulb needs a ballast to strike the arc and hold it at steady power, and the picks in this guide run on 35 W ballasts. The Stage III kit includes 35 W Morimoto XB ballasts, and the ACME kit includes 35 W ACME SpeedyStart ballasts that reach full intensity in 3.5 seconds.
Standalone projectors need a separate kit. The Mini H1 9.0, the RWR Mini D2S 4.0, and the RWR H1 8.0 all need an HID conversion kit to light, which includes ballasts, bulbs, and a harness. LED bulbs will fit some projectors but perform worse than a HID kit per the seller.
Will a retrofit projector fit my headlights?
It depends on the housing size and depth. A 2.5-inch projector fits most H4 and H7 housings with little cutting, while a 3.0-inch projector needs a larger opening. The Mini H1 9.0 lists a minimum housing depth of 115 mm and a 20 mm mounting shaft, so measure the space behind the reflector before buying.
Shroud choice affects fit too. A shroud that is too wide will hit the housing wall, while a shroud that is too small leaves a gap around the lens. The picks here list the shrouds they fit, so match the shroud to the housing opening as well as to the lens.
How long does a retrofit install take?
Plan on a full day for a first install, including time to open the housings, mount the projectors, wire the ballasts and harness, aim the beams, and reseal the lenses. A complete kit with matched parts saves time, since the ballasts, bulbs, and harness all fit together without extra matching.
Rushing the seal causes fogging. Take time to clean the old sealant, lay fresh butyl sealant, and press the lens back on evenly, then let the seal set before the first drive. A housing that fogs after a retrofit usually needs the seal redone. A second set of hands helps when the lens goes back on, since one person can hold the housing steady while the other presses the lens into the seal and checks the edge for gaps.
Conclusion
For most drivers, the Morimoto Mini H1 Stage III is the best HID projector for retrofit work, because it pairs H1 9.0 projectors with matched 35 W ballasts, bulbs, and a harness in one box. Tight housings suit the Mini H1 9.0 alone, while budget builds can start with the ACME kit. The RWR picks suit builders who want a sharp beam from one lens.
Write Your Review
No reviews yet. Be the first to share your experience!