Solar panels make power in the middle of the day, while most homes use it in the evening. The best home batteries for solar close that gap, storing daytime energy for the night. This guide compares six verified home storage systems, from a 5 kWh modular unit to a 15 kWh whole-home battery, to match storage to the size of your home.
Quick verdict
The six systems below cover every home size, and the split sits between fixed-capacity units and modular stacks. A single 13.5 or 15 kWh unit covers most homes in one box, while a modular system starts small and grows as needs change. Read the comparison first, then study the system that matches your roof and your loads.
| System | Usable capacity | Continuous power | Best for | Main limit |
|---|---|---|---|---|
| Tesla Powerwall 3 | 13.5 kWh | 11.5 kW | New solar, whole home | Certified installer only |
| Enphase IQ Battery 5P | 5.0 kWh | 3.84 kVA | Modular growth | Needs system controller |
| FranklinWH aPower 2 | 15 kWh nominal | 10 kW | Largest single unit | Usable figure varies |
| Generac PWRcell 2 | 9 to 36 kWh | 5.2 to 11.5 kW | Modular, generator pairing | NMC chemistry |
| Sigenergy SigenStor | 8.76 kWh per module | 4.6 kW per module | EV charging tower | Newer brand, recall noted |
| Homegrid Stack’d | 4.8 kWh per module | 8.6 to 14.4 kW per stack | 48V modular stacks | Module only, lead time |
How we selected
Every system in this guide comes from a page opened and read in full, with stock status and specifications taken from that page or from the maker datasheet it cites. We kept the set distinct from the companion solar-storage guides, which already cover more than two dozen other brands.
The companion guides already cover EG4, SOK, Fortress Power, SimpliPhi, Pytes, Jakiper, Zendure, Goal Zero, Pecron, Dabbsson, EcoFlow, Rolls, Crown, U.S. Battery, Deka, Trojan, LG, SolarEdge, BYD, Huawei, Sonnen, LiTime, Renogy, and SunGoldPower. The result is a fresh set of six systems from different makers.
Home storage has two numbers that matter above all others: usable capacity in kilowatt hours, which sets how long the battery runs, and continuous power in kilowatts, which sets what it can run at once. A 15 kWh battery with 5 kW of output runs small loads for a long time, while a 10 kWh battery with 10 kW of output runs big loads for a shorter time. We weighed both figures for each system, and we noted every case where two sources gave different numbers for the same figure.
Coupling and compatibility matter just as much. A DC-coupled battery with a built-in inverter suits a new solar install, while an AC-coupled battery suits an existing solar array from any inverter brand. A 48V modular battery suits an off-grid inverter, while a system with embedded microinverters suits a home already running that brand. Match the system to the solar you have or plan to buy, and confirm the installer and the permits before ordering.
The six systems in detail
Each system below earned its place by being on sale through its maker or a dealer page we opened, with capacity and power figures from the maker datasheet. Read the lead paragraph for the headline facts, then the detail paragraphs for the numbers that decide whether the system fits your home.
Tesla Powerwall 3
The Tesla Powerwall 3 is a 13.5 kWh home battery with a built-in 11.5 kW solar inverter, 11.5 kW continuous power output, and 97.5 percent round-trip efficiency from solar to home. It suits a new solar install where one unit replaces both the string inverter and the battery.
The datasheet-verified figures give 13.5 kWh of usable capacity, 15.4 kW peak power off-grid, and a 185 LRA motor-start rating that can start a central air conditioner. Six MPPT trackers accept up to 20 kW DC of solar, with an MPPT range of 150 to 480V and a 600V maximum. The chemistry is LFP, depth of discharge is 100 percent, cycle life is 6,000 cycles, and the warranty runs 10 years with 70 percent capacity retention. The unit measures 1098 by 609 by 193 mm, weighs 130 kg or 287 lbs, works from minus 20 to 50 degrees C, and carries a NEMA 3R rating for indoor or outdoor mounting. Up to four units stack for 54 kWh and 46 kW.
Storm Watch pre-charges the battery before severe weather, and Heat Mode keeps the unit charging in temperatures down to minus 4 degrees F. The system can also connect to a compatible Model 3, Model Y, or Cybertruck to use the vehicle battery for longer backup. Two figures need noting: one review page calls the chemistry NMC, while the datasheet-verified sources give LFP, and the same page lists 22 kW peak power against the datasheet figure of 15.4 kW. We use LFP and 15.4 kW. The unit sells only through Tesla-certified installers. Buy it if you want the highest continuous power in a single all-in-one unit. Skip it if you want to retrofit an existing string-inverter array without rewiring.
Enphase IQ Battery 5P
The Enphase IQ Battery 5P is a 5 kWh AC-coupled home battery with six embedded IQ8D-BAT microinverters, 3.84 kVA continuous output at 240V, and LFP chemistry. It suits a home that wants to start small and add storage in 5 kWh steps, with each unit adding 5 kWh and 3.84 kVA.
The dealer listing gives the full specification. Usable capacity is 5.0 kWh, continuous output is 3.84 kVA at 240V and 3.33 kVA at 208V, and peak output is 7.68 kVA for three seconds and 6.14 kVA for ten seconds. Round-trip efficiency is 90 percent AC and 96 percent DC. The warranty runs 15 years or 6,000 cycles, with capacity retention above 60 percent. Dimensions are 38.6 by 21.7 by 7.4 inches. Charging runs from minus 4 to 122 degrees F, discharging from minus 4 to 131 degrees F, and the optimal range is 32 to 86 degrees F. Cooling is passive with no fans, and the unit mounts on a wall or an optional pedestal, indoors or outdoors. Motor starting reaches 48A LRA, and up to eight units stack for 40 kWh.
Backup needs more than the battery alone. An IQ System Controller, a gateway, and communication equipment are required, and the battery does not isolate the home from the grid by itself. One review page claims 8,000 cycles, while the warranty terms give 6,000, so we use 6,000. Buy it if you already run Enphase microinverters and want modular growth. Skip it if you need whole-home backup from a single unit, since one 5P gives 5 kWh and 3.84 kVA.
FranklinWH aPower 2
The FranklinWH aPower 2 is a 15 kWh AC-coupled home battery with a built-in 10 kW continuous inverter and 15 kW surge power for 10 seconds. It is the largest single-unit capacity in this guide, and it suits whole-home backup including central air conditioning.
The dealer listing gives nominal energy of 15 kWh, usable energy of 13.6 kWh, nominal voltage of 51.2V, and round-trip efficiency above 90 percent. Peak output is 15 kW for 10 seconds, with 25 kW transient for one second and a 185 LRA motor-start rating. Dimensions are 45.2 by 29.5 by 11.8 inches, or 1149 by 750 by 300 mm, and weight is 357 lbs, or 162 kg. The enclosure is IP67 for the battery and IP56 for the wiring, and operating temperature runs from minus 4 to 122 degrees F. Noise is about 30 dBA. The warranty runs 15 years or 60 MWh throughput, with more than 6,000 cycles at 80 percent depth of discharge. Up to 15 units connect to one aGate controller for 225 kWh.
Usable capacity needs a note. The dealer spec table gives 13.6 kWh usable from 15 kWh nominal, while several review pages describe the unit as 15 kWh usable. We report the dealer table figure and note the difference. The aGate smart controller is required, and it brings a native generator port, black-start capability, and grid-forming operation. Buy it if you want the biggest single battery in this guide with generator support. Skip it if you want a standalone battery, since the aGate is part of the system.
Generac PWRcell 2
The Generac PWRcell 2 is a modular home battery system built from 3 kWh DCB modules in a cabinet that holds three to six of them, giving 9 to 18 kWh per cabinet and up to 36 kWh with two cabinets. It suits a home that wants to grow storage over time and pair the battery with a Generac generator.
The maker spec sheet gives usable energy of 9, 12, 15, 18, and 36 kWh for the M3, M4, M5, M6, and M6 times two configurations, with maximum continuous power of 5.2, 7, 8.7, 10.5, and 11.5 kW. Maximum AC start capacity is 65, 87, 108, 130, and 130A, and maximum backup PV size is 7.5, 10, 12.5, 15, and 15 kW. Round-trip efficiency is 88 percent. Battery modules carry a 10-year or 7.56 MWh throughput warranty, while the inverter, cabinet, and smart disconnect switch carry 10 years. Each DCB module is 3 kWh at 46.8V nominal, with 1.75 kW maximum continuous power, dimensions of 17.3 by 17.7 by 3.3 inches, and weight of 55 lbs. The cabinet measures 10.75 by 23 by 70 inches, and the installed unit weighs 278, 333, 388, and 443 lbs for M3 through M6.
The chemistry is lithium nickel manganese cobalt, or NMC, rather than the LFP used by most systems in this guide. Charging runs from 23 to 122 degrees F and discharging from minus 4 to 122 degrees F, with derating possible above 104 degrees F and below 32 degrees F. The system is AC-coupled, pairs with Generac generators from 9 to 28 kW, works with Generac PWRmicro and Enphase IQ8 inverters, and includes an ecobee smart thermostat and PWRmanager load control. The smart disconnect switch gives a transfer time under 50 ms and supports backup up to 200A. One older homeowner guide lists 5.1, 6.9, and 8.6 kW for M3 through M5, against the spec sheet figures of 5.2, 7, and 8.7 kW, so we use the spec sheet. Buy it if you want modular growth with generator pairing from one maker. Skip it if you prefer LFP chemistry.
Sigenergy SigenStor
The Sigenergy SigenStor is a five-in-one tower that stacks a hybrid inverter, battery modules, power conversion, energy management, and an optional DC EV charger into one floor-standing unit. It suits a home that plans to add an EV and wants charging built into the same stack as the battery.
The installer page we opened gives the BAT 9.0 module at 9.04 kWh nominal and 8.76 kWh usable, with 4.6 kW continuous charge and discharge per module and 6.9 kW peak for 10 seconds. A tower takes one to six modules for 9.04 to 54.24 kWh, and a smaller BAT 6.0 module holds 6.02 kWh. The cells are LFP, 314 Ah, rated to 10,000 cycles. Single-phase inverters run 5, 6, 8, and 10 kW with 2 to 4 MPPTs, and three-phase inverters run 5, 10, 15, and 25 kW. Backup switchover takes 5 milliseconds, the optional DC EV charger runs 12.5 or 25 kW and is V2X-ready, the enclosure is IP66, ambient range is minus 20 to 55 degrees C, and the warranty runs 10 years to 70 percent capacity retention.
Two caveats apply. In November 2025 Sigenergy issued a voluntary recall in Australia covering single-phase 8, 10, and 12 kW energy controllers sold between March and November 2025, where a quick-connect AC plug could overheat. The recall did not involve the battery modules, and current stock ships with a redesigned connector. Module naming also varies by region and year, with earlier datasheets listing BAT 5.0 and BAT 8.0 modules, so confirm the exact module on the quote. Sigenergy was founded in 2022, so its track record is shorter than the other makers in this guide. Buy it if you want the most integrated tower with EV charging built in. Skip it if you want the longest maker history.
Homegrid Stack’d 4.8 kWh module
The Homegrid Stack’d module is a 4.8 kWh LFP battery module at 48V nominal, designed to stack two to eight high on a shared BMS and base. It suits an off-grid or hybrid home that wants 48V storage in 4.8 kWh steps, with a 10-year warranty and a wide inverter list.
The dealer listing gives nominal capacity of 100 Ah at 48V DC, with a system operating range of 46 to 56V DC and round-trip efficiency above 98 percent as published by the maker. A complete stack holds 9.6 to 38.4 kWh, and up to 15 stacks in parallel reach 576 kWh. Continuous power output is 8.6 to 14.4 kW per complete stack depending on configuration, with surge power up to 24 kW for 10 seconds. Each module measures 29 by 15.75 by 5.25 inches and weighs about 108 lbs. The enclosure is IP55, charging runs from 32 to 113 degrees F, discharging from 14 to 131 degrees F, and communication runs over CAN and RS485 through the BMS. The maker lists compatibility with Sol-Ark, Schneider Electric, SMA, Victron Energy, and OutBack Power inverters. Cycle life is up to 6,000 cycles at 80 percent depth of discharge.
This listing is for one module only, not a standalone system. A working stack needs the Stack’d BMS and base, sold separately, plus at least two modules, and the module cannot connect directly to solar panels. The listing notes an extended lead time with shipping in December 2026, so confirm the delivery date before ordering. One dealer page lists continuous output up to 15 kW, against the 8.6 to 14.4 kW range on the listing we opened, so we use the listing range. Buy it if you want 48V modular storage that grows by 4.8 kWh at a time. Skip it if you want a complete battery in one box.
How to pick home batteries for solar
Picking a home battery for solar starts with your evening load. List the appliances that run after sunset, note their power draw, and estimate how many hours they run. Then size the battery so its usable capacity covers that evening load with a margin, and its continuous power covers the biggest loads that run at the same time.
How much storage do home batteries for solar need
Home batteries for solar need enough usable capacity to cover the evening load after the panels stop producing, which is about 8 to 14 kWh for most homes. A single 13.5 kWh Powerwall 3 or a 15 kWh aPower 2 covers that range in one unit, while two Enphase 5P units give 10 kWh and three give 15 kWh.
A home with an EV or electric heating needs more, and a modular stack grows to meet it.
Usable capacity is the figure to use, not nominal capacity. The FranklinWH aPower 2 lists 15 kWh nominal and 13.6 kWh usable on the dealer table, while the Sigenergy BAT 9.0 lists 9.04 kWh nominal and 8.76 kWh usable. Read the usable figure for every system you compare, and size the stack so the usable total covers the evening load with at least 20 percent margin.
Continuous power and motor starting
Continuous power sets what the battery can run at once, and motor starting sets what it can start. A central air conditioner needs 3 to 5 kW to run and a large starting surge, which is why the Powerwall 3 lists 185 LRA, the aPower 2 lists 185 LRA, and the PWRcell 2 lists up to 130A of AC start capacity.
A battery with 3.84 kVA continuous output, such as a single Enphase 5P, runs a refrigerator, lights, and outlets, but not a central air conditioner on its own.
Add up the loads that run at the same time during an outage, and compare the total with the continuous power figure. Then check the motor-start figure for the largest motor in the home, and confirm the battery can start it. If the numbers fall short, add a second unit or a second stack rather than hoping the loads never overlap.
DC-coupled or AC-coupled
A DC-coupled battery connects to the panels through a hybrid inverter, which keeps the energy in DC form and avoids an extra conversion. An AC-coupled battery connects on the AC side of the home, which suits an existing solar array from any inverter brand.
The Powerwall 3, Sigenergy SigenStor, and Homegrid Stack’d follow this path, and they suit a new solar install where the inverter and the battery arrive together. The Enphase 5P, FranklinWH aPower 2, and Generac PWRcell 2 follow this path.
Retrofit needs care. The Powerwall 3 is DC-coupled, so adding it to an existing string-inverter array means rewiring the panels to its DC inputs. An AC-coupled battery drops into the same home without touching the panels. Check the existing inverter and the panel wiring before choosing, and get the installer to confirm the coupling in writing.
Warranty, chemistry, and installer
Warranty terms vary widely across this guide. The Enphase 5P and FranklinWH aPower 2 run 15 years per unit, the Powerwall 3, PWRcell 2, SigenStor, and Stack’d run 10 years, and the throughput caps differ, from 7.56 MWh for a PWRcell 2 module to 60 MWh for an aPower 2.
Read the retention floor too: the Powerwall 3 and SigenStor hold 70 percent at year 10, while the 5P holds above 60 percent after 6,000 cycles.
Chemistry varies as well. Five systems in this guide use LFP, while the Generac PWRcell 2 uses NMC. LFP brings longer cycle life and a wider temperature range, while NMC brings higher energy density in a smaller cabinet. Every system in this guide needs a certified installer and a permit, so confirm the installer, the lead time, and the interconnection rules with your utility before ordering.
FAQ
These questions cover the points readers ask most often after comparing the six systems. Each answer uses only the figures from the opened product pages and maker datasheets, plus general buying knowledge that applies to any home battery. Read them before you choose, so the system you buy fits the home you own.
Can home batteries for solar run a whole house
Yes, home batteries for solar can run a whole house during an outage if the capacity and the continuous power cover the loads. A single Powerwall 3 gives 13.5 kWh and 11.5 kW, which runs most homes including central air conditioning. A single aPower 2 gives 15 kWh nominal and 10 kW, which also covers whole-home backup.
A single Enphase 5P gives 5 kWh and 3.84 kVA, which covers essential loads only.
Whole-home backup also needs the right controller. The Powerwall 3 needs its backup gateway, the 5P needs an IQ System Controller, the aPower 2 needs its aGate, and the PWRcell 2 needs its smart disconnect switch. Size the battery to the loads, confirm the controller, and ask the installer to list the protected loads in writing.
How long does a home battery last during an outage
Runtime depends on the usable capacity and the average load. A 13.5 kWh battery running a 1 kW average load lasts about 13 hours, while the same battery running a 3 kW average load lasts four hours. A refrigerator, lights, internet, and a gas furnace draw about 1 kW together, while adding a central air conditioner raises the draw to 4 kW or more.
Plan the outage loads in advance, and set the battery to reserve a portion of its charge for the night. A battery that runs the whole house at full load will drain fast, while a battery that runs essential loads only can stretch through a long outage. Check the app during the outage and shed loads as the charge falls.
Can you add more batteries later
Yes, every system in this guide grows, but the path differs. The Powerwall 3 stacks up to four units for 54 kWh, the Enphase 5P stacks up to eight units for 40 kWh, the aPower 2 stacks up to 15 units per aGate for 225 kWh, and the SigenStor stacks one to six modules per tower for up to 54 kWh.
The PWRcell 2 adds modules from three to six per cabinet and a second cabinet for 36 kWh, and the Stack’d system stacks two to eight modules per stack and up to 15 stacks for 576 kWh. Adding later costs more than buying the full size at once, since the installer returns and the permits repeat. Size the first purchase for the loads you have now plus the loads you plan in the next few years, such as an EV or a heat pump, and keep the growth path in mind when you choose the system.
Adding later costs more than buying the full size at once, since the installer returns and the permits repeat. Size the first purchase for the loads you have now plus the loads you plan in the next few years, such as an EV or a heat pump, and keep the growth path in mind when you choose the system.
Do home batteries work without solar panels
Yes, most home batteries in this guide can charge from the grid and discharge during peak-rate hours or outages, even without solar panels. The Enphase 5P supports battery-only energy management in approved configurations, and the other systems can charge from the grid as well.
Without solar, the battery acts as a backup and time-of-use device rather than a solar storage device.
A battery without solar still needs the right controller and the utility interconnection approval. Check the local rules, since some utilities limit battery-only systems or require a different permit. Solar adds the most value, since it refills the battery every day without grid power.
Conclusion
The best home batteries for solar are the ones that match your evening load, your biggest motors, and the solar you already own. The Powerwall 3 and aPower 2 cover whole-home backup in one unit, the Enphase 5P and Stack’d grow in small steps, and the PWRcell 2 pairs with a generator. Size the capacity and confirm the installer before you buy.
Write Your Review
No reviews yet. Be the first to share your experience!