An Arlo camera that loses power at the wrong moment leaves a gap in coverage, so the cell you choose matters. The best batteries for arlo wireless camera models depend on the generation: the original Wire-Free takes CR123A cells, while Arlo Pro and Pro 2 take a rechargeable pack. This guide compares six options with published specs.
Quick verdict
For the original Arlo Wire-Free, the Energizer 123 is the most balanced CR123A choice, with a 1500 mAh typical capacity and a wide operating range. Panasonic CR123A is the bulk-buy pick, while the MCYIERDE 2-pack is the practical route for Arlo Pro and Pro 2 owners.
If you own the original Arlo Wire-Free camera, you need four CR123A lithium cells per change, and the cells below all meet that requirement. The Energizer 123 leads because its datasheet publishes a 1500 mAh typical capacity, a 1500 mA continuous discharge rating, and a 3500 mA pulse rating, which covers the short bursts that night vision and motion recording demand. Panasonic CR123A matches it on shelf life and adds a slightly higher 1550 mAh nominal capacity, so it is the better pick when you stock spares for several cameras. Duracell DL123A and Streamlight CR123A sit close behind, with the same 3 volt output and 10 year shelf life, while SureFire SF123A stands out for the widest temperature range in this group. For Arlo Pro and Pro 2, the disposable CR123A cells do not fit at all, so the MCYIERDE rechargeable pack is the only option in this list that works, and it ships as a two-pack with a dual charger so one pack can charge while the other runs the camera.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| Energizer 123 | CR123A lithium, disposable | Original Arlo Wire-Free | 1500 mAh, 3.0 volts | Sold in small packs |
| Duracell DL123A | CR123A lithium, disposable | Original Arlo Wire-Free | 3.0 volts, under 1 percent self-discharge per year | No capacity figure published on the opened pages |
| Panasonic CR123A | CR123A lithium, disposable | Multi-camera homes | 1550 mAh, 3 volts | Bulk 24-pack may exceed what one camera needs |
| SureFire SF123A | CR123A lithium, disposable | Extreme cold and heat | Operates from minus 76 to 176 degrees F | No capacity figure published on the opened page |
| Streamlight CR123A 85180 | CR123A lithium, disposable | Outdoor cameras and spares | About 1550 mAh, 3 volts | Availability not shown on the opened page |
| MCYIERDE A-1 A-1B 2-pack | Rechargeable lithium-ion pack | Arlo Pro and Pro 2 | 2440 mAh, 7.2 volts | Fits Pro and Pro 2 only |
How we selected batteries for Arlo wireless cameras
Selection started from the battery each Arlo generation actually takes, then narrowed to cells with published specs from maker datasheets and listing pages. Only cells with a stated voltage, chemistry, and shelf life or cycle detail made the list, and every figure below comes from a page opened during research.
The first filter was fit. The original Arlo Wire-Free camera takes four 3 volt CR123A lithium cells, while Arlo Pro and Pro 2 take a single 7.2 volt rechargeable pack, part number VMA4400, and those two formats cannot be swapped between generations. A replacement guide opened during research confirms the split and lists the VMA5400 pack for Arlo Pro 3, Pro 4, Pro 5S, Ultra, and Ultra 2, which is why this article keeps the two formats separate instead of ranking them against each other. The second filter was published evidence. Each CR123A cell here has a maker datasheet or a listing page that states its voltage, chemistry, operating temperature range, and shelf life, and the rechargeable pack has a listing page that states its capacity, voltage, and included charger. Cells that appear in roundups without a readable product page were left out. The third filter was cold-weather behavior, since outdoor cameras face winter nights. Every CR123A in this list is rated for operation at minus 40 degrees F or lower, and the SureFire cell extends that floor to minus 76 degrees F. Weight, pack size, and self-discharge rate were noted where the pages state them, because a camera on a high mount is easier to service when spares last for years in a drawer.
Battery picks in detail
Each pick below lists the exact product name, the Arlo models it fits, the specs the maker or listing page publishes, and the limits that matter before you buy. Read the fit note first, because the wrong format will not seat in the camera at all. Check the model first.
Energizer 123 lithium battery
The Energizer 123 is the reference CR123A for the original Arlo Wire-Free, and its datasheet publishes the most complete electrical detail in this group. It suits owners who want a cell with stated numbers for capacity, discharge, and temperature rather than a generic claim.
The maker lists the Energizer 123 as a lithium manganese dioxide cell with a 3.0 volt nominal voltage, a 1500 mAh typical capacity measured to 2.0 volts, and a weight of 16.5 grams. The datasheet lists a maximum discharge of 1500 mA continuous and 3500 mA pulse, which covers the short current bursts that infrared night vision and motion-triggered recording draw. Storage and operating temperature both run from minus 40 degrees C to 60 degrees C, which the datasheet also gives as minus 40 degrees F to 140 degrees F. The cell carries a positive temperature coefficient device to limit current during short circuit conditions, and it is UL listed under MH12454. The listing page states a shelf life of up to 10 years and describes a built-in vent, and the pack on the listing page holds four cells. Arlo rates a fresh set of four CR123A cells in the original Wire-Free for roughly 4 to 6 months based on five minutes of active recording per day, so a four-pack covers one full change with no spare left over. Pros: the most complete published specs in this group, strong pulse rating for night vision, and a 10 year shelf life. Cons: the four-pack leaves no spare cell, and the datasheet capacity is typical rather than a minimum. Buy it if you run one original Wire-Free camera and want the best-documented cell. Skip it if you run several cameras and want a bulk pack.
Duracell DL123A lithium battery
The Duracell DL123A is a 3 volt lithium cell for the original Arlo Wire-Free, and its listing page highlights a very low self-discharge rate. It suits owners who keep spare cells in a drawer for months between changes. Its long storage life makes it a natural spare.
The maker lists the DL123A as a 3 volt non-rechargeable lithium cell with a cylindrical shape measuring 17 mm in diameter and 34.5 mm in height, and the datasheet gives a nominal voltage of 3.0 volts with a typical voltage of 3.2 to 3.3 volts. The listing page states that the cell loses less than 1 percent of its charge per year and offers a shelf life of up to 10 years, which makes it a strong choice for cameras that see infrequent use or for spares stored as backup. The datasheet lists an operating temperature range of minus 20 degrees C to 75 degrees C, given as minus 4 degrees F to 167 degrees F, and an average weight of 17.0 grams. The listing page describes a leak-resistant design with sealing technology that limits leakage risk, and the pack on the listing page holds two cells. The datasheet does not state a capacity figure in the text the fetch returned, so this article does not give one for the DL123A, and the listing page also omits it. The two-pack covers half of one four-cell change, so owners of a single camera need two packs per change. Pros: very low self-discharge for long storage, 10 year shelf life, and leak-resistant sealing. Cons: no capacity figure on the opened pages, and the two-pack is small for a four-cell camera. Buy it if you value long storage life and keep spares on hand. Skip it if you want a published capacity figure to compare runtimes.
Panasonic CR123A lithium battery
The Panasonic CR123A is the bulk pick for homes with more than one original Arlo Wire-Free camera, sold here as a 24-pack with the highest nominal capacity in this group. It suits owners who change cells in several cameras and want spares ready at once.
The maker lists the Panasonic CR123A as a 3 volt lithium cell with a nominal capacity of 1550 mAh, a diameter of 17.0 mm, a height of 34.5 mm, and a weight of about 16.0 grams. The datasheet lists a continuous drain of 20 mA and an operating temperature range of minus 40 degrees C to 70 degrees C, and it notes that the cell is suited to cameras and lights because of high-rate discharge. The listing page states a shelf life of up to 10 years in storage and lists the pack as 24 batteries, which covers six full four-cell changes for one original Wire-Free camera. The datasheet is dated July 2024 and identifies the cell as a Panasonic Energy product with applications that include security devices, which covers the camera use case. With 1550 mAh nominal capacity against the Energizer 1500 mAh typical figure, the Panasonic cell offers a small capacity edge on paper, though the two figures use different test conditions and should not be read as a direct runtime promise. Pros: the highest nominal capacity in this group, a 10 year shelf life, and a 24-pack that covers many changes. Cons: the bulk pack may be more cells than a single-camera home needs, and the datasheet gives a modest 20 mA continuous drain figure. Buy it if you run two or more original Wire-Free cameras. Skip it if you own a single camera and do not want a large spare stock.
SureFire SF123A lithium battery
The SureFire SF123A is the cold-weather pick in this group, with the widest operating temperature range of any cell here. It suits cameras mounted in exposed spots that face deep winter cold or summer heat. Its fault protection shuts the cell down if it overheats.
The listing page states that the SureFire SF123A is a 3 volt lithium battery with a ten-year shelf life and that lithium cells retain up to 90 percent of their original power output capability after 10 years of storage. The page lists a working output from minus 76 degrees to 176 degrees F, given as minus 60 degrees to 80 degrees C, which is far wider than the minus 40 degree floor of the other CR123A cells in this list. The page describes a built-in fault protection that causes the battery to shut down should overheating occur, and it notes that a lithium battery maintains fairly constant voltage for up to 95 percent of its life, depending on discharge rate. The listing page shows the product as in stock with more than one pack option, and it notes that the cell is optimized for use in SureFire lights. The page does not state a capacity figure, so this article does not give one for the SF123A. The wide temperature range is the main reason to choose it over the other cells, since a camera on an exterior wall can sit in direct sun by day and freezing air at night. Pros: the widest temperature range here, fault protection, and steady voltage through most of the discharge. Cons: no capacity figure on the opened page, and the listing is aimed at flashlight users rather than camera owners. Buy it if your camera faces extreme temperatures. Skip it if you want a published capacity figure.
Streamlight CR123A 85180 lithium battery
The Streamlight CR123A 85180 is a 3 volt lithium cell sold as a six-pack, and its listing page publishes a full spec table. It suits owners who want a mid-size pack with stated capacity, temperature range, and shelf life in one place. The six-pack leaves two spares after a change.
The listing page lists the Streamlight 85180 as a lithium manganese dioxide primary battery, non-rechargeable, with a voltage of 3 volts and a nominal capacity of typically around 1550 mAh. The page gives an operating temperature range of minus 40 degrees F to 140 degrees F, given as minus 40 degrees C to 60 degrees C, and a shelf life of 10 years minimum. The pack holds six batteries, which covers one full four-cell change for an original Wire-Free camera with two spares left over, and the page lists the UPC as 080926851801. The page states that the cell maintains a consistent 3 volt output through its operating life and that the six-pack format keeps spares on hand. The page also warns not to recharge these primary cells and not to mix old and new batteries in the same device. One limit to note: the fetched copy of the listing page did not show an availability marker, so the stock status could not be read from the page itself, even though the product is listed for sale. Pros: a full spec table on one page, a six-pack that leaves two spares, and a 10 year shelf life. Cons: the fetched page did not show a stock marker, and the capacity is given as typically around 1550 mAh rather than a fixed figure. Buy it if you want a six-pack with two spares after each change. Skip it if you need a stock marker visible on the page before ordering.
MCYIERDE A-1 A-1B replacement battery 2-pack
The MCYIERDE 2-pack is the rechargeable route for Arlo Pro and Pro 2, replacing the VMA4400 pack that Arlo no longer manufactures as a new original part. It suits Pro and Pro 2 owners who want a spare pack ready on the charger. One pack runs the camera while the other charges.
The listing page states that this pack is compatible with Arlo Pro and Pro 2 cameras, including models VMA4400, VMC4030, VMC4030P, VMS4230, VMS4430, and VMS4530, and it lists a battery capacity of 2440 mAh with a voltage of 7.2 volts. The product is a two-pack of lithium-ion batteries with a dual USB charger, model name MC-A1-2D, and the listing gives a battery weight of 180 grams. A replacement guide opened during research confirms that Arlo Pro and Pro 2 use a rear-loading 7.2 volt, 2440 mAh rechargeable pack labeled VMA4400, also stamped A-1, A-1B, or A-1C, and that Arlo no longer manufactures new original VMA4400 packs, which is why third-party packs are the practical route now. The guide also notes that charging a VMA4400 battery inside the camera through its Micro-USB port needs a 9 volt Quick Charge adapter, while the included dual charger avoids that requirement entirely. Keeping one pack in the camera and one on the charger removes downtime, since a depleted pack can be swapped in seconds. Pros: a two-pack with a dual charger, exact 2440 mAh and 7.2 volt match for Pro and Pro 2, and no need for a special wall adapter. Cons: it fits Pro and Pro 2 only, and the listing page copy available during research was crawled in March 2026. Buy it if you own an Arlo Pro or Pro 2 and want a charged spare ready. Skip it if you own a newer Arlo model, because this pack will not fit it.
Buying guide
Arlo changed battery formats across generations, so the model number decides the battery before any brand comparison begins. The notes below cover fit, format, weather, storage, and the mistakes that waste money. Read the fit note first, then compare capacity and temperature range.
Match the battery to your Arlo wireless camera model
The original Arlo Wire-Free camera, model VMC3030, takes four 3 volt CR123A lithium cells in a hinged bottom compartment. Arlo Pro and Pro 2, models VMC4030 and VMC4030P, take a single rear-loading 7.2 volt rechargeable pack, part number VMA4400. Check the model on the camera body or in the Arlo app before ordering.
Arlo Pro 3, Pro 4, Pro 5S, Ultra, and Ultra 2 take a different slide-out pack, part number VMA5400, while Arlo Essential cameras have a sealed battery that cannot be swapped at all. A pack made for an Arlo Pro 2 will not fit an Arlo Pro 4, and CR123A cells will not fit any Pro model. If the camera is an original Wire-Free, any of the five CR123A cells in this guide fits, and the choice comes down to capacity, temperature range, and pack size.
CR123A or rechargeable pack for an Arlo wireless camera
The format is decided by the camera, not by preference. Original Wire-Free cameras run on disposable CR123A cells, and the replacement guide notes that rechargeable 123A cells rated for Arlo exist, but standard 3.0 volt rechargeable cells can drop below the camera voltage cutoff, so disposable lithium cells are the straightforward choice.
Arlo Pro and Pro 2 run on the rechargeable VMA4400 pack, and a two-pack with a charger is the practical setup because one pack charges while the other runs the camera. Newer Pro 3, Pro 4, Pro 5S, and Ultra models run on the VMA5400 pack, which is a different size and voltage, so none of the products in this guide fits those models. When the camera model is unclear, the battery door gives the answer: a bottom compartment with four cylindrical slots means CR123A, while a rear door with a single rectangular pack means VMA4400.
Cold weather and outdoor mounting
Outdoor cameras face the coldest hours of the night, and lithium chemistry holds voltage far better than alkaline in freezing air. Every CR123A in this guide is rated for operation at minus 40 degrees F or lower, and the SureFire SF123A extends that floor to minus 76 degrees F, which makes it the pick for cameras on exposed walls in harsh winters.
Cold still shortens runtime, and the replacement guide notes that busy walkways, long clip durations, and frequent live viewing all shorten the 4 to 6 month estimate that Arlo gives for a fresh set of four cells. Mount the camera where the battery door can be reached without a ladder when possible, and keep a spare set indoors so a winter change does not mean handling cold cells with bare hands. Store spare cells in a cool, dry place in their original packaging, and keep them away from metal objects that could bridge the terminals.
Shelf life and spare sets
All five CR123A cells in this guide list a shelf life of up to 10 years, and the Duracell DL123A adds a self-discharge rate of under 1 percent per year, so a spare set bought today stays ready for years. For a house with several cameras, that storage life makes bulk packs worth buying.
That long shelf life makes bulk packs practical: the Panasonic 24-pack covers six full changes for one original Wire-Free camera, while the Streamlight six-pack covers one change with two spares left over. Keep one full set of four cells as a spare for each camera, and check the battery percentage in the Arlo app regularly rather than waiting for the camera to shut off. The replacement guide suggests swapping or recharging around 25 percent to 30 percent, because lithium voltage drops steeply at the very end of a discharge cycle and a camera can die between visits to a second home. For Pro and Pro 2, the same logic favors a two-pack, since a charged spare on the dock means the camera is offline only for the seconds a swap takes.
What to avoid when buying CR123A cells
Three mistakes cause most CR123A problems in Arlo cameras. First, never mix old and new cells in the same camera, because voltage imbalance can cause early low-battery warnings and uneven discharge, and the replacement guide warns against mixing partially drained cells with fresh ones.
Second, do not use alkaline photo cells as a substitute, because alkaline voltage sags rapidly under the night-vision infrared load and the camera can shut off early. Third, check the listing before buying a budget CR123A, because off-brand cells often deliver far less than their stated capacity, and a listing that omits voltage, chemistry, or shelf life gives no way to judge the cell. Buy from a listing that states the voltage, chemistry, and shelf life on the page, and match the cell to the camera model before ordering.
FAQ
These answers cover the questions Arlo owners ask most often about batteries, from runtime to mixing cells. Each answer uses only figures from pages opened during research. If your model is not listed here, check the battery door or the Arlo app before ordering.
How long do batteries last in an Arlo wireless camera?
Arlo rates a fresh set of four CR123A cells in the original Wire-Free camera for roughly 4 to 6 months based on five minutes of active recording per day. Real use varies: busy walkways, cold winter temperatures, long clip durations, and frequent live viewing all shorten that estimate, while quiet locations stretch it.
The replacement guide notes that cameras needing new batteries more often than every 3 to 6 months usually benefit from power management settings in the Arlo app. For Arlo Pro and Pro 2, the 2440 mAh rechargeable pack follows the same pattern, with motion frequency and temperature deciding how often a swap is needed. Check the battery percentage in the app and swap around 25 percent to 30 percent to avoid a camera dying between visits.
Can I use rechargeable CR123A cells in the original Arlo Wire-Free?
The replacement guide states that the original Wire-Free camera can take 3.7 volt ICR17335 rechargeable cells rated for Arlo, but it warns that standard 3.0 volt rechargeable cells drop below the camera voltage cutoff almost immediately. That cutoff behavior is why disposable lithium cells are the default in this guide.
Disposable 3 volt CR123A lithium cells are the straightforward choice, and all five CR123A picks in this guide are disposable cells. Rechargeable 123A cells rated for Arlo typically hold around 800 mAh, roughly half the capacity of a 1500 mAh disposable cell, so they need charging about twice as often. If you choose rechargeables, buy cells marked as rated for Arlo and charge them only in an external charger, since the camera has no charging port for CR123A cells.
Do Arlo Pro and Pro 2 use the same battery?
Yes. Arlo Pro, model VMC4030, and Arlo Pro 2, model VMC4030P, both use the same rear-loading 7.2 volt, 2440 mAh rechargeable lithium-ion pack, part number VMA4400, also stamped A-1, A-1B, or A-1C on the battery label. The MCYIERDE 2-pack in this guide lists compatibility with both models and with the VMA4400 part number.
The pack loads through a hinged rear door, and it can be charged inside the camera through a Micro-USB port with a 9 volt Quick Charge adapter, or in the included dual charger. Newer models do not share this pack: Arlo Pro 3, Pro 4, Pro 5S, Ultra, and Ultra 2 use the VMA5400 pack instead.
Can I mix old and new CR123A cells in one camera?
No. The replacement guide states that all four depleted CR123A cells should be removed at the same time and that old partially drained batteries should never be mixed with fresh ones, because voltage imbalance can cause early low-battery warnings or cell leakage.
The Streamlight listing page gives the same warning and adds that mixing different battery types in the same device can lead to uneven discharge and reduced performance. Always replace all four cells in an original Wire-Free camera at once, and keep the removed cells together so they are not mixed with fresh spares by mistake. The same rule applies to any device that takes more than one cell.
Why does my Arlo camera drain batteries faster in winter?
Cold air lowers the voltage a lithium cell can hold under load, and winter nights are also the longest period of infrared night-vision use, which draws the highest current. The replacement guide lists cold winter temperatures alongside busy walkways, long clip durations, and frequent live viewing as the factors that shorten that estimate.
All five CR123A cells in this guide are rated for operation at minus 40 degrees F or lower, so they keep working in the cold, but the runtime still drops compared with mild weather. The SureFire SF123A has the widest temperature range here, rated from minus 76 degrees to 176 degrees F, which makes it the pick for cameras in the coldest spots. Checking the battery percentage in the app during winter catches a weak set before it dies.
Conclusion
For the original Arlo Wire-Free, buy the Energizer 123 for the best-documented cell or the Panasonic CR123A 24-pack for several cameras. For Arlo Pro and Pro 2, buy the MCYIERDE 2-pack so a charged spare is always ready. Match the battery to the model first, check the pack size, and the rest follows.
Write Your Review
No reviews yet. Be the first to share your experience!