A flash that recycles slowly or stops mid-set can ruin a portrait session, so power choice matters as much as the light itself. This guide covers best batteries for flash photography in the form of lithium-ion packs for speedlights, pocket strobes and mirrorless cameras, with maker-listed capacities and fit notes for each pick.

Quick verdict

If you shoot events with a Godox speedlight, start with the Godox VB26B, since it pairs a 2980mAh rating with up to 480 full-power flashes. For a pocket strobe, the Godox WB29 gives the AD200Pro a larger 14.4V pack and over 500 full-power flashes. Camera owners should match the exact maker pack to the body.

Product Type Best for Key spec Main limit
Godox VB26B Lithium-ion speedlight pack Godox V1 and V860III flashes 7.2V, 2980mAh, 21.45Wh Fits listed Godox flashes only
Godox WB29 Lithium-ion strobe pack Godox AD200Pro pocket strobe 14.4V, 2900mAh, over 500 flashes 4 hours to fully charge
Canon LP-E6NH Lithium-ion camera pack Canon EOS R5, R6 and 5D Mark IV 7.2V, 2130mAh Needs a separate charger or USB PD body
Nikon EN-EL15c Lithium-ion camera pack Nikon Z8, Z6 II and D850 7.0V, 2280mAh, 16.0Wh Charger sold separately
Sony NP-FZ100 Lithium-ion camera pack Sony Alpha A7 III, A7R III and A9 7.2V, 2280mAh, 16.4Wh Charger sold separately
Fujifilm NP-W235 Lithium-ion camera pack Fujifilm X-T4, GFX100S and GFX50S II 7.2V, 2200mAh, 16Wh Needs an external wall charger

How we selected

We picked packs from pages opened for this guide, and we kept only models with a clear maker-listed capacity, voltage and fit. Each pick had to suit flash work in a direct way, either by powering a speedlight or strobe, or by keeping a mirrorless camera running through a long flash session. No pack entered the list from memory alone.

Flash photography puts a repeated, heavy load on a battery. A speedlight draws a short burst of high current for every pop, then needs power again for the next recycle. A weak pack shows up as a long wait between flashes, a dimmer pop near the end of a charge, or a camera that shuts down before the event ends. That is why capacity alone does not tell the whole story. Voltage, fit, charge method and the number of full-power flashes all shape how a pack behaves on a real job.

The six packs below cover two different jobs. The two Godox packs power the flash head itself. The four camera packs power the camera body, the autofocus system, the viewfinder and the screen while the flash fires. Many photographers need both kinds of spare, so this guide covers them as a matched set rather than as rivals. If you own a Godox V1, the VB26B is the direct fit. If you own an AD200Pro, the WB29 is the direct fit. If you own a Canon, Nikon, Sony or Fujifilm body, the maker pack for that body is the direct fit.

Every figure in the product sections comes from a page opened for this guide. Where a maker lists a range or a condition, the article keeps that condition in view. Where a maker does not state a figure, the article does not invent one. That approach keeps the comparisons honest, even when two packs look close on capacity alone. Read the fit list for each pack before you buy, because a pack that fits one mount or one flash family will not fit another.

Flash batteries in this guide

The six packs below span speedlight cells, a pocket strobe cell and four camera cells, so you can match power to the part of the kit that runs out first. Each section gives the maker-listed capacity and voltage, the models the pack fits, and the limits that matter on a long shoot.

Godox VB26B lithium-ion battery

The Godox VB26B is the current lithium-ion pack for the Godox V1 round-head flash and several related speedlights. The maker lists it at 7.2V and 2980mAh, with 21.45Wh of stored energy, and the manual states up to 480 full-power flashes from a full charge. That combination suits event work where the flash fires often.

The VB26B is an updated version of the VB26 and VB26A packs, and the maker lists it for the Godox V1 series, the V1Pro series, the V100 series, the V860III series, the V850III and the AD100Pro. The manual also names the MF-R76 macro ring flash in its compatibility image. That broad fit makes one spare useful across several Godox heads, as long as each head is on the maker list. Check the model code on your flash before you order, because older Godox heads outside the list use different packs.

Recycle speed is a key part of flash work, and the manual states a rapid recycle time of approximately 1.5 seconds with this pack. A fully charged pack can support up to 480 full-power flashes, depending on the flash model and usage conditions. Lower power settings stretch the count further, since each pop draws less charge, but the maker does not give a separate count for each power level. Plan your spare count around full-power use if you shoot receptions or dance floors at high output.

The pack weighs about 110g, which is 3.87 ounces, so a spare adds little weight to a camera bag. It charges in the Godox VC26 charger, which the manual lists with a 5V and 2.0A input and an 8.4V and 1A output. The charger shows charging status through an LED indicator, with a solid green light for a full charge. Keep the charger and a spare pack in the bag, and you can rotate packs while one charges from a USB source.

Storage and care follow the manual. For long-term storage, the maker recommends charging the pack to about 50 to 60 percent of capacity. Keep it in a cool, dry place away from direct sunlight and extreme heat, and charge and discharge it from time to time if it sits unused for a long stretch. The manual also lists six protection features in its diagram, covering over-voltage, over-temperature, over-discharge, over-current, over-charge and short circuit protection.

  • Pros
  • High 2980mAh capacity for a speedlight pack, with 21.45Wh of stored energy.
  • Up to 480 full-power flashes from a full charge, per the maker manual.
  • About 1.5 second recycle time, which suits fast event shooting.
  • Fits V1, V1Pro, V100, V860III, V850III and AD100Pro flashes.
  • Light at about 110g, so a spare is easy to carry.
  • Cons
  • Needs the dedicated VC26 charger, since the pack has no onboard charging port.
  • Fit is limited to the Godox models on the maker list.
  • Flash count falls with high-power use and with heavy continuous shooting.

Buy this pack if you shoot with a Godox V1, V860III, V850III or AD100Pro and you want a direct maker spare with a clear flash count. Skip it if your flash is not on the maker compatibility list, or if you need a pack with onboard USB charging, since the VB26B charges only in its dedicated charger.

Godox WB29 lithium-ion battery

The Godox WB29 is the lithium-ion pack for the Godox AD200Pro pocket strobe, a 200Ws flash that works as a portable studio light. The maker lists the pack at 14.4V and 2900mAh, and the AD200Pro manual states over 500 full-power flashes from a full charge. That output suits location portraits and outdoor flash work.

The AD200Pro manual lists a recycle range of 0.01 to 1.8 seconds, so the strobe can fire again quickly at low power and still returns in under 2 seconds at full power. Power adjusts from full power down to 1/256 in 81 levels, which gives fine control over exposure when you balance flash against daylight. The strobe supports high-speed sync up to 1/8000s, so you can use wide apertures outdoors while the flash fills in shadows.

Guide numbers help to place the AD200Pro in context. The manual lists a guide number of 60, in meters at ISO 100, with the bare bulb flash head and the AD-S2 standard reflector at 28mm, and a guide number of 52, in meters at ISO 100, with the speedlite flash head at 35mm. Those figures describe the strobe, not the battery alone, but they show why the WB29 needs a larger voltage and a larger cell than a speedlight pack. A 200Ws strobe draws more energy per pop, so the pack must hold more charge to keep the count high.

Charging takes planning. The manual states that it takes 4 hours to fully charge the battery by using the standard battery charger. That is a long charge, so an event shooter should charge the night before and carry a charged spare rather than relying on a mid-event top-up. The manual also states that the available charge and discharge times are 500, which describes the cycle life of the pack. Store a pack that will sit unused at about 60 percent charge, and recharge it fully if it has not been used for over 3 months.

The battery level shows on the AD200Pro panel in grids. Three grids mean a full battery, two grids mean a medium level, one grid means a low level, and a blank grid means the level is low and the pack needs a recharge. A blinking grid means the remaining charge is about to run out and the flash will switch off by itself in 1 minute. That clear display helps you swap packs before the strobe stops in the middle of a set.

  • Pros
  • Over 500 full-power flashes per charge, per the AD200Pro manual.
  • 14.4V and 2900mAh rating suits a 200Ws pocket strobe.
  • Recycle range of 0.01 to 1.8 seconds covers low and full power.
  • Clear panel grid display shows remaining charge at a glance.
  • High-speed sync up to 1/8000s suits outdoor fill flash.
  • Cons
  • Full charge takes 4 hours with the standard charger.
  • Pack fits the AD200 and AD200Pro family, not other Godox heads.
  • Heavier duty use at full power will shorten the flash count.

Buy this pack if you own an AD200Pro and you want a spare that keeps a 200Ws strobe firing through a long location session. Skip it if you shoot only with a small on-camera speedlight, since the WB29 is built for the larger AD200Pro body and will not fit a V1 or V860III.

Canon LP-E6NH lithium-ion battery

The Canon LP-E6NH is the high-capacity maker pack for Canon EOS R5, EOS R6 and related EOS bodies. The maker lists it at 7.2V and 2130mAh, which is 14 percent more capacity than the LP-E6N pack. That extra capacity helps a mirrorless camera keep its viewfinder, autofocus and flash control running through a long shoot.

Compatibility is broad within the Canon EOS line. The listing page names the EOS R5, EOS R6, EOS 5D Mark IV, EOS 6D Mark II, EOS R5 C, EOS 90D, EOS 5Ds, EOS R, EOS 5D Mark III, EOS 5D Mark II, EOS Ra, EOS 6D, EOS 7D Mark II, EOS 7D, EOS 5Ds R, EOS 80D, EOS 70D, EOS 60Da, EOS 60D, EOS R7 and EOS R6 Mark II. It is back compatible with cameras that use LP-E6 and LP-E6N packs, so it can serve as a higher capacity substitute in older bodies. Check your own body on the list, since some features differ by camera.

Charging gives two routes. The pack can be charged with an LC-E6 or LC-E6E mains charger, and it can also be charged in camera with compatible camera bodies that offer USB PD charging. That in-camera option is useful on location, since you can top up from a PD power source without carrying a separate charger. The maker notes that in-camera charging depends on the body, so confirm that your camera supports it before you rely on it.

The pack communicates with the camera, and the listing page states that selected EOS cameras can read the battery serial number, remaining capacity, shutter count after charging, recharge performance and date of last use. That data helps you track which spare has seen the most use and which one needs a rest. The pack is supplied with selected EOS cameras, and it is also sold as a spare for photographers who need a second or third pack for flash-heavy days.

Flash work draws on the camera as well as on the flash head. The camera must power autofocus, metering and the viewfinder while it tells the flash when to fire. A pack with more capacity gives the body more headroom for those tasks, which matters when you shoot bursts with flash or when you work in cold rooms where battery output drops. Carry at least one spare LP-E6NH if a single pack has ever run out before the end of an event.

  • Pros
  • 2130mAh capacity, 14 percent more than the LP-E6N pack.
  • Broad fit across EOS R, EOS 5D, EOS 6D, EOS 7D and EOS 90D bodies.
  • In-camera USB PD charging on compatible bodies.
  • Camera can read serial number, remaining capacity and recharge performance.
  • Same form factor as LP-E6 and LP-E6N, so it fits existing grips and chargers.
  • Cons
  • Needs an LC-E6 or LC-E6E charger unless the body supports in-camera charging.
  • Capacity gain over the LP-E6N is modest, at 14 percent.
  • Some older bodies may lose some functions with newer packs.

Buy this pack if you shoot Canon EOS mirrorless or DSLR bodies and you want a maker spare with a clear capacity gain and in-camera charging on supported bodies. Skip it if you shoot Nikon, Sony or Fujifilm, since the LP-E6NH fits Canon bodies only, or if your body already takes the newer LP-E6P pack for full performance.

Nikon EN-EL15c lithium-ion battery

The Nikon EN-EL15c is the highest capacity version of the EN-EL15 family, and the maker manual lists it at 7.0V and 2280mAh. A retailer listing gives the energy rating as 16.0Wh, and the manual lists dimensions of about 40 by 56 by 20.5mm and a weight of about 80g. That size keeps the pack light while giving a mirrorless body more run time.

Compatibility covers Nikon Z and DSLR bodies. The retailer listing names the Nikon Z8, Zf, Z7 II, Z7, Z6 II, Z6, Z5, D850, D780, D500 and D7500 as primary fits, and notes that the pack is back compatible with most cameras that take EN-EL15, EN-EL15a or EN-EL15b packs. The listing also notes that the Z8 needs the newer EN-EL15c or EN-EL15b pack to reach its highest performance modes, while older packs may limit the camera. Check the fit for your own body, since performance rules differ by model.

In-camera charging is a useful feature, with a limit. The retailer listing states that the EN-EL15c supports in-camera battery charging and direct power delivery via USB-C when used in compatible modern mirrorless cameras such as the Z8, Zf, Z7 II, Z6 II and Z5. The same listing warns that the camera body must also support the feature, so an older DSLR will power the camera but will not charge the pack through a USB cable. That distinction matters when you plan a location kit around a power bank.

The dedicated charger is the Nikon MH-25a, which the retailer listing names as the charger for this pack, and the listing states that the charger is sold separately. Nikon does not include a wall charger when you buy the battery on its own, so a first-time buyer should check whether a charger came with the camera body. The manual states an operating temperature range of 0 to 40 degrees C, which is 32 to 104 degrees F, and it advises storing the pack in a cool, dry place away from extreme heat.

Flash sessions on Nikon Z bodies draw on the pack for autofocus, subject tracking, the electronic viewfinder and the screen, as well as for flash control. A higher capacity pack gives more margin for those loads, and the EN-EL15c is the top capacity in its family. The retailer listing states that the pack offers about 20 percent more power than the older EN-EL15a, which is a clear gain for event and wedding work where the camera stays on for hours.

  • Pros
  • 2280mAh capacity, the highest in the EN-EL15 family to date.
  • 16.0Wh energy rating at 7.0V, with a light 80g weight.
  • In-camera USB-C charging and power delivery on compatible Z bodies.
  • Broad back compatibility with EN-EL15, EN-EL15a and EN-EL15b bodies.
  • Small size, about 40 by 56 by 20.5mm, fits existing battery grips.
  • Cons
  • Charger is sold separately, so a new buyer may need the MH-25a.
  • In-camera USB charging needs a body that supports the feature.
  • Older EN-EL15 packs may limit performance on the newest Z bodies.

Buy this pack if you shoot a Nikon Z8, Z6 II, Z7 II, Z5 or D850 and you want the highest capacity EN-EL15 pack with USB-C charging on supported bodies. Skip it if you need a pack with a charger in the box, or if your camera takes a different Nikon battery family, since the EN-EL15c will not fit other battery slots.

Sony NP-FZ100 lithium-ion battery

The Sony NP-FZ100 is the Z-series maker pack for Sony Alpha mirrorless cameras, and the manual lists it at 7.2V and 2280mAh, with 16.4Wh of stored energy. The manual lists dimensions of 1.52 by 2.04 by 0.89 inches and a weight of 2.9 ounces. That capacity suits long flash sessions where the camera stays on for hours at a time.

Compatibility covers the main Sony Alpha bodies that use the Z-series pack. The manual names the Sony Alpha A7 III, A7R III and A9 digital cameras, and other compatible Z-series devices. Retailer listings extend that fit to the A9 II, A7R IV, A7S III, A6600 and Alpha 1, among others. Check the fit list for your own body, since Sony has used several battery families across its Alpha line, and only Z-series bodies take this pack.

The pack uses Sony InfoLITHIUM technology, which lets a compatible camera display the remaining battery charge as a percentage on the camera LCD screen or viewfinder. That reading helps you judge when to swap packs during a flash session, rather than guessing from a simple bar icon. The manual advises carrying spare, fully charged NP-FZ100 packs for prolonged shooting, which is sound advice for event work where a single pack may not last the day.

Charging needs a compatible Sony battery charger, which is sold separately, or charging directly in a compatible camera. The manual states that the pack should be fully charged before its first use, and that the charger indicator will show charging status, typically in orange or green. For long-term storage, the manual recommends charging the pack to about 50 percent of capacity and keeping it in a cool, dry place away from direct sunlight and extreme temperatures.

Flash work on a Sony Alpha body is demanding, since the camera runs autofocus, eye tracking, the electronic viewfinder and the screen while it drives the flash. The NP-FZ100 gives those systems a larger reserve than the older NP-FW50 pack, and the manual notes its high capacity for extended shooting times. A spare in the bag is a simple way to avoid a mid-event shutdown when the flash and the camera both draw heavily on power.

  • Pros
  • 2280mAh capacity with 16.4Wh of stored energy.
  • InfoLITHIUM display shows remaining charge as a percentage.
  • Fits A7 III, A7R III, A9 and other Z-series Alpha bodies.
  • Compact size at 1.52 by 2.04 by 0.89 inches.
  • Light at 2.9 ounces, so a spare is easy to carry.
  • Cons
  • Charger is sold separately, so a new buyer needs a Sony charger.
  • Fits Z-series bodies only, not Sony bodies that use other packs.
  • Capacity drops with heavy video, continuous shooting and cold use.

Buy this pack if you shoot a Sony Alpha A7 III, A7R III, A9 or another Z-series body and you want a maker spare with a clear percentage readout. Skip it if your Sony body takes the NP-FW50 or another pack, since the NP-FZ100 will not fit that battery slot.

Fujifilm NP-W235 lithium-ion battery

The Fujifilm NP-W235 is the maker pack for the Fujifilm X-T4 and related GFX bodies, and the manual lists its amperage as 2200 milliamps. A detailed label study gives the nominal voltage as 7.2V, the charging voltage limit as 8.4V, and the nominal energy as 16Wh. The manual lists the weight as 3.21 ounces, which is 91 grams.

Compatibility covers Fujifilm X and GFX bodies. The manual names the Fujifilm X-T4, GFX100S and GFX50S II, and notes that the pack also fits the VG-XT4 vertical battery grip. Other listings extend the fit to the X-T5, X-H2, X-H2S and X-S20, among others. Check the fit for your own body, since Fujifilm has used several battery families, and only NP-W235 bodies take this pack. The manual states that the pack is not compatible with cameras from other makers.

Charging needs an external wall charger, which is not included with the battery itself. The manual states that the pack requires an external wall charger for charging, and that you should connect the battery to a compatible Fujifilm charger and plug the charger into a power outlet. That means a first-time buyer should confirm that a charger came with the camera or grip, or buy one with the spare pack. For long-term storage, the manual recommends charging the pack to about 50 percent of capacity.

The label study explains a point that confuses many buyers. The pack carries a printed rated capacity of 2200mAh, while the nominal capacity derived from the model name is 2350mAh. The two figures come from different measurement conditions, and the rated capacity is the figure to use for formal comparison. The nominal energy of 16Wh comes from the rated capacity and the nominal voltage, and it gives a fair way to compare this pack with packs at different voltages.

Flash work on a Fujifilm body draws on the pack for autofocus, the electronic viewfinder and the screen, as well as for flash control. The NP-W235 is a higher capacity pack than the NP-W126S used in older X bodies, and it suits the X-T4 and GFX bodies that run larger sensors and faster processors. Carry a spare if you shoot events, since a single pack may not cover a full day of flash work.

  • Pros
  • 2200mAh rated capacity with 16Wh of nominal energy.
  • 7.2V nominal voltage with an 8.4V charging limit.
  • Fits X-T4, GFX100S, GFX50S II and the VG-XT4 grip.
  • Clear rated and nominal capacity figures on the label.
  • Compact size at 2.1 by 1.5 by 0.9 inches.
  • Cons
  • Needs an external wall charger, which is not included.
  • Rated and nominal capacity figures can confuse buyers.
  • Fits NP-W235 bodies only, not older Fujifilm bodies.

Buy this pack if you shoot a Fujifilm X-T4, X-T5, X-H2, GFX100S or GFX50S II and you want a maker spare with a clear 2200mAh rated capacity. Skip it if your Fujifilm body takes the NP-W126S pack, since the NP-W235 will not fit that battery slot.

Buying guide for the best batteries for flash photography

Buying a flash battery starts with fit, not with capacity. A pack that does not match your flash head or camera body is useless, no matter how large its rating looks. Check the model code on the flash or camera, then match it to the maker list for the pack. This section walks through the checks that matter most for flash work.

Match the pack to the flash or camera first

Fit is the first check, and it is also the easiest check to get wrong. Speedlight packs fit only the flash heads on the maker list, and camera packs fit only the bodies that use that battery family. The Godox VB26B fits V1, V1Pro, V100, V860III, V850III and AD100Pro flashes, while the WB29 fits the AD200Pro.

Camera packs follow the same rule, so a Canon LP-E6NH will not fit a Nikon body, and a Sony NP-FZ100 will not fit a Fujifilm body. Write down your flash and camera model codes before you shop, and compare them line by line with the maker fit list.

Some packs look alike but differ in a small way. The Nikon EN-EL15 family has several versions, and the newest Z bodies need the EN-EL15c or EN-EL15b for full performance. The Fujifilm NP-W235 has a rated capacity of 2200mAh and a nominal capacity of 2350mAh, so a listing that quotes only one figure can mislead. The Canon LP-E6 family has LP-E6, LP-E6N, LP-E6NH and LP-E6P versions, and the newest R5 Mark II needs the LP-E6P for full performance. When in doubt, buy the maker pack for your exact body, not a pack that looks close.

Read capacity in watt-hours as well as milliamp-hours

Milliamp-hours alone can mislead when packs run at different voltages. A 2900mAh pack at 14.4V holds far more energy than a 2900mAh pack at 7.2V, because energy is capacity times voltage. Watt-hours give a fair comparison across packs, and the maker lists watt-hours for several packs in this guide.

The VB26B lists 21.45Wh, the EN-EL15c lists 16.0Wh, the NP-FZ100 lists 16.4Wh, and the NP-W235 lists 16Wh. Use those figures to compare packs, and use milliamp-hours only to compare packs at the same voltage.

Flash count is a more direct figure for flash packs. The VB26B manual states up to 480 full-power flashes, and the AD200Pro manual states over 500 full-power flashes with the WB29. Those counts describe full-power use, so lower power settings will give more flashes per charge. Camera packs do not list a flash count, since the camera and the flash share the load in different ways. For camera packs, treat capacity and watt-hours as the guide, and carry a spare if a single pack has ever run out early.

Plan recycle time and flash count for your shoot

Recycle time shapes how fast you can shoot with flash. The VB26B manual states about 1.5 seconds for a full-power recycle, and the AD200Pro manual lists a recycle range of 0.01 to 1.8 seconds. At low power, the flash returns almost at once. At full power, the wait is longer, and a tired pack will take longer still.

If you shoot dance floors or sports with flash, test your recycle time at the power level you plan to use, and carry a fresh pack for the busiest part of the event.

Flash count shapes how many spares you need. A pack that gives 480 full-power flashes may cover a portrait session, but a wedding with several hundred guests may need two or three spares. Count your flashes from a past event if you can, and add a margin for cold rooms, high power use and burst shooting. A spare pack is small and light, so carrying one more is a low cost way to avoid a missed shot. Rotate packs through the day, and keep the freshest pack for the most important moments.

Check charging time and charging options

Charging time varies widely across packs. The WB29 takes 4 hours to fully charge with the standard charger, so it needs an overnight charge before a long shoot. The VB26B charges in the VC26 charger, which takes a 5V and 2.0A input and gives an 8.4V and 1A output.

Camera packs vary too, and some bodies support in-camera USB charging while others need a separate charger. The LP-E6NH supports in-camera USB PD charging on compatible bodies, and the EN-EL15c supports in-camera USB-C charging on compatible Z bodies.

Plan charging around your shoot, not around a single pack. Charge all spares the night before, and keep a charger in the car or bag if the venue has power. If your body supports in-camera charging, a PD power source can top up a camera pack between sets, but it will not charge a speedlight pack. For speedlight and strobe packs, the only route is the dedicated charger, so pack that charger and its cable. Label your packs so you know which ones are fresh and which ones need a charge.

Carry spares and rotate them through the day

A single pack is rarely enough for a full flash event. The camera, the flash head and the strobe each draw power, and each one can run out at a different time. Carry at least one spare for each pack type you use, and rotate them so no single pack does all the work.

Swap a speedlight pack when the recycle time starts to grow, not when the flash stops. Swap a camera pack when the percentage readout falls low, not when the camera shuts down.

Storage between shoots matters too. Several manuals in this guide recommend storing lithium-ion packs at about 50 to 60 percent of capacity for long-term storage, in a cool, dry place away from direct sunlight and extreme heat. A pack left fully charged or fully flat for months may lose capacity faster. Check your spares before a big event, charge them fully, and test them in the flash or camera. A pack that has sat unused for months may need a full recharge before it gives its normal flash count.

FAQ

These answers cover the questions photographers ask most often about flash batteries, from flash counts to charging and fit. Each answer uses only the maker-listed facts from the product sections above, plus general buying advice that applies across packs. If a figure is not listed by the maker, the answer says so rather than guessing.

What are the best batteries for flash photography for weddings?

For weddings, the best batteries for flash photography are the packs that match your own flash and camera, with enough spares to cover the whole day. A Godox V1 shooter should carry the VB26B, with at least one spare, since the maker lists up to 480 full-power flashes per charge.

An AD200Pro shooter should carry the WB29, with a spare, since the maker lists over 500 full-power flashes. Camera owners should carry a spare maker pack for the body, such as the LP-E6NH, EN-EL15c, NP-FZ100 or NP-W235, depending on the camera. Charge all packs the night before, and rotate them through the day.

How many full-power flashes can a speedlight battery give?

The count depends on the pack and the flash head. The Godox VB26B manual states up to 480 full-power flashes from a full charge, depending on the flash model and usage conditions. The Godox WB29 manual states over 500 full-power flashes for the AD200Pro.

Lower power settings give more flashes per charge, since each pop draws less energy, but the maker does not list a separate count for each power level. Camera packs do not list a flash count, since the camera and flash share the load. Plan around the full-power count, and carry a spare if your shoot needs more flashes than one pack can give.

Can I charge a flash battery in the camera?

Speedlight and strobe packs cannot be charged in a camera. The VB26B charges only in the Godox VC26 charger, and the WB29 charges only with its standard charger. The Canon LP-E6NH charges in camera on bodies with USB PD, and the Nikon EN-EL15c can be charged in camera with compatible Z-series bodies that support USB-C charging.

The Sony NP-FZ100 can be charged directly in a compatible camera, and the Fujifilm NP-W235 needs an external wall charger. Check your own body, since in-camera charging depends on the camera model.

Do camera batteries affect flash recycle time?

The camera battery does not set the flash recycle time, but it does power the camera systems that control the flash. The flash head has its own pack, and that pack sets the recycle time for the flash itself. The VB26B gives about 1.5 seconds at full power, and the AD200Pro with the WB29 gives 0.01 to 1.8 seconds across its power range.

A low camera battery can still cause trouble, since the camera may slow autofocus, dim the viewfinder or shut down. Keep both the flash pack and the camera pack charged, and swap either one when its level falls low.

How should I store spare flash batteries?

Store lithium-ion packs in a cool, dry place away from direct sunlight and extreme heat. Several manuals in this guide recommend charging a pack to about 50 to 60 percent of capacity for long-term storage, and charging and discharging it from time to time if it sits unused.

The WB29 manual recommends storing a pack at about 60 percent charge, and recharging it fully if it has not been used for over 3 months. Keep terminal covers on when the pack is not in use, and keep packs away from metal objects that could short the contacts. Check spares before a shoot, and charge them fully.

Conclusion

Match the pack to your flash or camera first, then check capacity, flash count and charging time. The VB26B suits Godox speedlights, the WB29 suits the AD200Pro, and the Canon, Nikon, Sony and Fujifilm packs suit their own bodies. Carry spares, charge them the night before, and rotate them through the day for steady flash work.

Related guides

Browse all Buying Guides guides →