A home solar array only works after sunset if the storage behind it is sized and matched with care, and the best batteries for home solar power are the 48V LiFePO4 units built for fixed home systems. This guide compares six battery-only models with no built-in inverter, to help you size a bank and match an inverter.
Quick verdict
The EG4 PowerPro WallMount leads on raw capacity at 14.3 kWh per unit, while the five smaller modules suit homes that want to start small and add units later. Every pick below is a 48V LiFePO4 battery-only unit, so each one needs a separate inverter and charge controller to form a working solar system.
| Product | Capacity | Best for | Key spec | Main limit |
|---|---|---|---|---|
| EG4 PowerPro WallMount All Weather 280Ah | 14.3 kWh | Large banks and outdoor walls | 280 Ah, IP65 rating | 308.6 lbs and a large wall footprint |
| SOK SK48V100N | 5.12 kWh | Rack builds on a budget | 100 Ah, 3U rack design | IP20 rating, so indoor use only |
| Fortress Power eFlex 5.4 | 5.4 kWh | Wall, rack, or floor mounting | 105 Ah, IP65 rating | 60 A max continuous discharge |
| SimpliPhi PHI 3.8 48V | 3.87 kWh | Small loads and long cycle life | 10,000+ cycles at 80% DOD | 37.5 A max continuous discharge |
| Pytes V5 | 5.12 kWh | Scalable banks with remote monitoring | Up to 16 modules in parallel | 75 A recommended continuous current |
| Jakiper JK48V100PRO | 5.12 kWh | Serviceable rack builds | 100 Ah, steel case | 20 A recommended charge current |
If you want the fewest boxes on the wall, the EG4 unit stores the most energy per module, and one unit already holds more than two of the 5.12 kWh modules combined. If you want to grow a bank one module at a time, the SOK, Fortress, Pytes, and Jakiper units all sit near 5 kWh, while the SimpliPhi module is the smallest block at 3.87 kWh and the easiest to fit into a tight space.
How we selected
We started from the keyword and kept only 48V LiFePO4 batteries made for fixed home solar storage, with no built-in inverter and no portable power station features. Each model below had its figures read from a maker page or maker spec sheet that was actually opened, and any figure that did not appear on an opened page was left out of this guide.
Capacity, continuous current, cycle life, temperature range, mounting style, and communication support carried the most weight, because those figures decide how many modules a home needs and which inverters will work with them. Weight and size mattered too, since a wall unit at more than 300 lbs needs very different planning from a rack module near 100 lbs.
Models that had been replaced by a newer version, or that showed a discontinued notice on the page we opened, were left out and noted in the sources file. The six models below are all current maker listings, and each one is a battery-only unit that pairs with a separate 48V inverter and solar charge controller.
Six 48V batteries for home solar power
These six units cover the main shapes of home solar storage: one large wall battery, three rack modules, one flexible wall, rack, or floor unit, and one compact modular block. All six use lithium iron phosphate chemistry, all six run at 48V nominal, and all six are designed to be wired in parallel so a bank can grow as a home adds panels or loads.
EG4 PowerPro WallMount All Weather 280Ah
The EG4 PowerPro WallMount All Weather 280Ah is the capacity leader in this group, and it suits homes that want a large bank with as few modules as possible. The maker lists 14.3 kWh of total energy capacity at 25C and 100% SOC, with a nominal voltage of 51.2V and a capacity of 280Ah, so a single unit covers a full evening of typical home use.
The maker lists a max continuous charge current of 140A and a max continuous discharge current of 140A, with 200A available as a max continuous current for 30 minutes. The built-in BMS is rated at 200A, and the internal busbars are rated to 600A, which supports paralleling multiple batteries and feeding multiple inverters. The unit also carries an on-board LCD touch screen and RS485 and CAN communication ports, with selectable closed-loop communication for EG4, Schneider, Sol-Ark, Victron, Growatt, Megarevo, Luxpower, and Deye inverters.
Outdoor placement is a real strength here. The maker lists an IP65 ingress protection rating and an integrated self-heating feature that warms the battery when the ambient temperature is low. The charging range is 32F to about 122F, and the discharging range is -4F to about 131F. Cycle life is listed at over 8000 cycles at 0.5C and 80% DOD, the design life is over 15 years, and the maker lists a 10 year warranty. Certifications listed on the spec sheet are UL1973 and UL9540A.
The trade-off is size and weight. The maker lists dimensions of 36.1 x 22.3 x 9.1 in. and a weight of 308.6 lbs., so this is a two-person lift that needs a strong wall, a mounting bracket, and clear space around it. The maker also lists a SOC cutoff of 20 percent, with a note recommending that value be set no lower than 20 percent to maintain the recommended 80 percent depth of discharge. Buy it if you want the biggest single block of storage and an outdoor-rated wall unit. Skip it if your wall space is tight or you prefer to start with a small bank and add modules later.
SOK SK48V100N
The SOK SK48V100N is a 3U rack-mount module that suits homes building a bank inside a standard rack or cabinet. The maker spec sheet lists a nominal voltage of 51.2V, a nominal capacity of 100Ah, and energy of 5120Wh, which makes it a straightforward 5.12 kWh building block that stacks neatly with more of the same.
The maker lists a recommended charge current of 50A and a maximum charge current of 100A, with a maximum continuous discharge current of 100A and a peak discharge current of 120A per minute. The recommended charge voltage is up to 58.4V, and the sheet lists CAN and RS485 communication with support for a long list of inverters, including Victron, SMA, SOFAR, Voltronic, MPP, Outback, Sol-Ark, Solis, Goodwe, Deye, Growatt, Schneider, and Sunsynk. The sheet also notes a 3U rack-mount design, an on and off switch, self-heating, and Bluetooth support.
Temperature figures are generous for an indoor rack unit. The maker lists a discharge temperature range of -4 to 140F and a charge temperature range of -4 to 122F, with a storage temperature range of 23 to 95F. The case is listed as SPCC plus SGCC steel, the enclosure protection is listed as IP20, the terminals are M8 type, and the dimensions are listed as 19.14 x 16.95 x 5.22 in. with an approximate weight of 100 lb.
The IP20 rating is the main limit, since it means this module belongs indoors in a rack, cabinet, or dry utility room rather than on an exposed outdoor wall. The maker does not state a cycle life figure or a warranty term on the opened spec sheet, so buyers should ask the dealer for those two figures before ordering. Buy it if you want a rack module with wide inverter support and a self-heating feature for cold rooms. Skip it if you need an outdoor-rated case or a single module with a much higher continuous current.
Fortress Power eFlex 5.4
The Fortress Power eFlex 5.4 is the most flexible unit in this group for placement, since the maker describes it as fitting a standard 19 in. server rack, sitting directly on a concrete floor, or mounting on a wall. The maker lists total energy of 5.4 kWh and a capacity of 105Ah, with a voltage range of 44 to 58.4V.
The maker lists a max charge current of 100A continuous and a max discharge current of 60A continuous, with a max pulse current of 130A for 5 seconds. That 60A continuous discharge figure is worth noting, since it sets the steady output of a single unit, while the 130A pulse figure covers short surges. The maker also lists MODbus and CANbus communication, data communication with popular hybrid inverters, and compatibility with Schneider, Sol-Ark, MidNite Solar, OutBack Power, SMA, and Morningstar inverters.
Durability figures are strong. The maker lists an IP65 dust and water proof design, a 10 year warranty with unlimited partial cycles, and a round-trip efficiency of over 98 percent. Life cycles are listed at 6000 at 80% DoD, and certifications listed are UL9540, UL1973, and UL1642. The charging temperature range is 32 to 113F, the discharging temperature range is 32 to 140F, and the storage temperature range is 32 to 95F.
The dimensions are listed as 21.5 x 17.5 x 7.2 in. with a weight of 116 lbs., so one person can still move it with care, but a wall mount still needs solid fixings. The main limit is the 60A max continuous discharge, which means larger loads will need two or more units in parallel. Buy it if you want one unit that can go on a wall, in a rack, or on the floor with an outdoor-rated case. Skip it if a single module must carry a heavy continuous load on its own.
SimpliPhi PHI 3.8 48V
The SimpliPhi PHI 3.8 48V, model PHI-3.8-48-M, is the smallest block in this group, and it suits homes that want to start with a modest bank and expand later. The listing page gives a total capacity of 3.87 kWh at 100% DOD, a nominal voltage of 51.2 VDC, a voltage range of 48 VDC to 56 VDC, and amp-hours of 75 Ah.
Continuous output is the figure to plan around. The maker lists a max discharge rate of 37.5 ADC, equal to 1.9 kW DC, and the same 37.5 ADC figure for the max charge rate. The surge rate is listed at 80 ADC, equal to 4.1 kW DC, for 10 minutes, which covers motor starts and short peaks. The page also notes an accessible 100A DC breaker for system control and a BMS, plus a modular design that allows parallel connection of multiple units to increase total capacity.
Longevity figures stand out for a unit this size. The maker lists a cycle life of 10,000+ cycles at 80% DOD, a round-trip efficiency of 96 percent, and a 10-year warranty. The operating temperature range is listed as -4F to 140F, and the page lists UL 9540 and UL 9540A certifications. The weight is listed at 86 lbs., and the chemistry is lithium ferro phosphate, described on the page as cobalt-free, with no cobalt in the cells.
The limit is output per module. At 1.9 kW DC continuous, one PHI 3.8 module suits light and medium loads, and a home with a large inverter will need several in parallel to use the inverter fully. The page asks buyers to contact the seller for availability, so confirm stock and delivery time before planning an install date. Buy it if you want a compact, long-life module and a bank that grows one small block at a time. Skip it if you need high continuous output from a single unit.
Pytes V5
The Pytes V5 is a modular 5.12 kWh unit built around scale, and it suits homes that expect their storage needs to grow over time. The maker describes the V5 Series as a flexible, scalable battery system built around a 5.12 kWh lithium iron phosphate battery module, with a rated voltage of 51.2V and a capacity of 100Ah.
The maker lists a recommended continuous charge and discharge current of 75A, with a maximum continuous rate of up to 100A, plus higher peak rates for short periods. That gap between the recommended 75A figure and the 100A maximum matters for sizing, since a bank planned around the recommended figure will run cooler and last longer than one planned around the maximum. The maker also lists a cycle life of over 6,000 cycles and a design life exceeding 10 years.
Scaling is the headline feature. The maker states that users can connect up to 16 modules in parallel in a single group, and that multiple groups can be linked through a hub to reach larger capacities, with total system sizes possible from tens to hundreds of kilowatt hours depending on the application. The V5 Series also supports remote monitoring and firmware upgrades through WiFi, and it includes an integrated heating pad that helps maintain performance in colder climates.
The maker does not state weight, dimensions, or a warranty term in years on the opened page, so those figures should be confirmed with the dealer before ordering. The other limit is that the 75A recommended current keeps a single module near the middle of the pack for steady output, even though the 100A maximum looks higher on a spec sheet. Buy it if you want a bank that can grow to 16 modules in one group with remote monitoring built in. Skip it if you need full weight and size figures from the maker page before you commit.
Jakiper JK48V100PRO
The Jakiper JK48V100PRO is a rack-style module with a strong focus on monitoring and protection, and it suits owners who want to see what is happening inside the pack. The maker spec sheet lists a nominal voltage of 51.2V, a nominal capacity of 100Ah, and energy of 5120Wh, with a smart battery management system and six temperature sensors.
The maker lists a maximum charge current of 100A and a maximum continuous discharge current of 100A, with a BMS discharge current high warning at 125A and a BMS discharge cut-off current of 130A for 1000ms. The recommended charge current is listed at 20A, and the recommended charge voltage is listed as 56V for the initial charge and 58.4V after 30 cycles. The BMS charge cut-off voltage is listed as over 59.2V, and the short circuit protection is listed at 300 microseconds.
Temperature figures are wide. The maker lists a discharge temperature range of -4 to 140F, a charge temperature range of 23 to 131F, and a storage temperature range of 23 to 95F. The BMS high temperature cut-off is listed at 149F, with a reconnect temperature of 140F. The case material is listed as steel, the terminal type is M8x4, the recommended connection wire is 6 AWG, and the dimensions are listed as 442 x 460 x 177 mm with an approximate weight of 48 kg.
The main limit is the 20A recommended charge current, which means charging at the recommended rate takes longer than charging at the 100A maximum, so solar sizing should allow for that. The maker does not state a cycle life figure or a warranty term on the opened spec sheet, so confirm both with the dealer before ordering. Buy it if you want a rack module with detailed BMS protection figures and six temperature sensors. Skip it if you need fast charging at the recommended rate from a single module.
Buying guide for home solar power batteries
Choosing storage for a home solar system is mostly a sizing exercise, and the figures in this guide are the raw material for it. Start with how much energy the home uses after sunset, then check continuous current against the largest loads, then confirm that the inverter and the battery share the same communication language.
How many batteries for home solar power do you need
Count the energy the home uses between sunset and sunrise, then divide by the usable energy of one module to get a first estimate of the bank size. A 5.12 kWh module holds about 5.12 kWh at full charge, but the usable share depends on the depth of discharge the maker recommends, so read the SOC cutoff on the spec sheet first.
Most homes need more than one module. One 5.12 kWh unit covers lights, a fridge, and small electronics for an evening, but an electric water heater, an air conditioner, or an electric oven will drain it fast. Two or three 5.12 kWh modules, or a single 14.3 kWh EG4 unit, give a bank real room to breathe, and a larger bank also cycles less deeply each night, which helps the cells last longer.
Leave room to grow. Rack modules such as the SOK, Pytes, and Jakiper units are made to be added in parallel, and the Pytes V5 allows up to 16 modules in a single group. Plan the rack space, the cabling, and the breaker layout for the bank you expect in two or three years, not just the bank you buy on day one.
Match the battery to your inverter
A 48V battery needs a 48V inverter, and the pair must agree on voltage limits, charge current, and communication. The EG4 unit lists closed-loop communication with eight inverter brands, and the SOK sheet lists Victron, Sol-Ark, Deye, Growatt, and Schneider. Check both manuals against each other before ordering.
Continuous current is the figure that decides whether the inverter can run at full output from batteries alone. The EG4 unit lists 140A max continuous discharge, the SOK and Jakiper units list 100A, the Fortress unit lists 60A, the Pytes unit lists 75A recommended, and the SimpliPhi unit lists 37.5A. Add the continuous current of every module in the bank and compare the total with the inverter draw at full load.
Voltage range matters as much as current. The Fortress unit lists a voltage range of 44 to 58.4V, the SimpliPhi unit lists 48 VDC to 56 VDC, and the Jakiper unit lists a recommended charge voltage of 56V to 58.4V. Set the inverter charge voltage inside the battery maker range, and never above the maximum the maker lists, since over-voltage charging shortens cell life.
Wall mount or rack mount
Mounting style decides where the bank can live and how much floor space it takes. The EG4 unit is a wall battery with a large footprint and a weight of 308.6 lbs., so it needs a strong wall and a proper bracket. The Fortress unit can go on a wall, in a rack, or on a concrete floor, which makes it the easiest to place in an awkward room.
Rack modules suit a tidy install. The SOK unit is a 3U rack-mount design, the Jakiper unit is a rack-style steel case, and the Pytes V5 is built for modular banks that grow module by module. A standard 19 in. rack keeps cabling short, keeps modules off the floor, and makes it easy to add one more unit later without rebuilding the whole bank.
Think about service access too. A wall unit needs clear space in front of it for the LCD screen and the cable connections, and a rack needs room to slide a module out. Leave the clearance the maker lists, keep the disconnect within reach, and make sure the room stays inside the temperature range on the spec sheet.
Cold weather and outdoor placement
Lithium iron phosphate cells charge poorly in the cold, so the temperature range and any heating feature deserve a close look. The EG4 unit lists an integrated self-heating feature and a charging range starting at 32F, the SOK sheet lists self-heating with a charging range starting at -4F, and the Pytes V5 includes an integrated heating pad.
Outdoor placement needs an outdoor-rated case. The EG4 unit and the Fortress unit both list an IP65 rating, which suits a covered outdoor wall or a patio install. The SOK unit lists an IP20 rating, which means it belongs indoors, and the Jakiper and SimpliPhi pages do not list an IP rating on the pages we opened, so treat those two as indoor units unless the dealer confirms otherwise.
Even an outdoor-rated battery needs shelter from direct sun and driving rain, and the charge controller should be set to respect the low-temperature charge limit on the spec sheet. A battery that cannot charge on a freezing morning will leave the home short of power the next evening, so cold-weather behavior is worth more attention than a headline capacity figure.
Plan for growth and daily cycling
A home solar battery cycles every day, so cycle life and depth of discharge shape its cost over time. The SimpliPhi unit lists 10,000+ cycles at 80% DOD, the EG4 unit lists over 8000 cycles at 80% DOD, the Fortress unit lists 6000, and the Pytes V5 lists over 6,000. The SOK and Jakiper sheets do not state a cycle life figure, so ask the dealer.
Depth of discharge is the other half of the same question. The EG4 sheet recommends a SOC cutoff of 20 percent to maintain 80 percent depth of discharge, and the SimpliPhi page lists capacity at 100% DOD alongside the 10,000+ cycle figure at 80% DOD. Running a bank to 100 percent every night will wear it faster than stopping at 80 percent, even when the maker allows full discharge.
Plan the bank so that a normal night uses about half to two-thirds of the stored energy, and keep one spare slot in the rack or one spare space on the wall for a future module. A bank that runs shallow cycles and still has room to grow will serve the home longer than a bank that is sized exactly to the limit on day one.
FAQ
These are the questions that come up most often when a home moves from panels alone to panels plus storage. The answers below use the figures from the six makers in this guide, and they assume a standard 48V hybrid or off-grid inverter paired with a battery-only unit.
Do I need an inverter with these batteries
Yes, every battery in this guide is a battery-only unit with no built-in inverter, so it cannot power a home on its own. The battery stores direct current energy, and a separate inverter turns that energy into the alternating current that home appliances use. A solar charge controller or a hybrid inverter also manages charging from the panels.
Pick the inverter first, then match the battery to it, or pick them as a pair from the compatibility list on the battery spec sheet. The EG4, SOK, and Fortress pages all list the inverter brands they communicate with, and closed-loop communication lets the inverter read the battery state of charge directly instead of guessing from voltage alone.
How long will a 5 kWh battery run a home
There is no single answer, since runtime depends on the loads and the continuous current the battery can deliver. A home drawing a steady 500 watts uses about 0.5 kWh per hour, while a home drawing 2,000 watts uses about 2 kWh per hour. Add up the watts of the loads you need, then divide the usable energy by that total.
Continuous current sets a second limit. A single SimpliPhi module delivers 1.9 kW DC continuous, a Fortress unit delivers 60A continuous, and a SOK or Jakiper unit delivers 100A continuous. If the loads need more than one module can deliver, add modules in parallel until the combined continuous current covers the largest load the home will run at once.
Can I mix different battery models
Mixing different models in one bank is a poor idea, even when the voltage matches. Different models have different capacities and BMS behavior, so one unit will charge and discharge faster than the others and the bank will drift out of balance. The makers in this guide all describe adding more of the same model in parallel.
If the home needs more storage later, buy the same model again and wire it in parallel with the existing bank, following the maker wiring guide. If the original model is no longer sold, the better path is a separate bank with its own inverter, or a full replacement of the bank with a current model.
How often do solar batteries need attention
LiFePO4 home batteries need little routine attention, but they still deserve a monthly check. Look at the BMS display to confirm that all modules show a similar state of charge and that the bank reaches full charge on sunny days. The Pytes V5 supports remote monitoring through WiFi, and the EG4 unit shows key figures on its LCD screen.
Keep the area around the bank clear, keep vents and fans free of dust, and check cable connections once a year for tightness and heat marks. If a module stops charging, shows a fault, or drifts far from the others in voltage, contact the installer or the dealer rather than opening the case, since the battery contains high-current connections.
Conclusion
The EG4 PowerPro WallMount is the pick for the biggest single block of storage, while the SOK, Fortress, Pytes, and Jakiper modules suit banks that grow one 5 kWh unit at a time. The SimpliPhi PHI 3.8 fits small loads with its long cycle life. Size the bank from evening use, match the inverter, and buy the model that fits the space.
Write Your Review
No reviews yet. Be the first to share your experience!