A short range projector sits close to the wall, so the screen must stay flat and face light that comes from below. The best portable projector screens for short range projectors use tensioned surfaces and light rejecting materials that keep the image bright in a room. This guide compares five portable screens that fold away when the show ends.

Quick verdict

Four of the five screens in this guide rise from the floor and are built for ultra short throw laser projectors, while one pull up screen suits short throw models that sit a little farther back. If you want the largest image, pick a 120 inch floor rising model. If you want the lightest setup, pick the pull up screen.

The NothingProjector Black Series gives the largest image in this group at 120 inches, with voice control and a perforated acoustic section at the bottom. The Screen Innovations Short Throw Lift matches it at 120 inches and adds a clamshell case that hides the screen when it is down. Both are made for short throw and ultra short throw projectors, and both use a 0.6 gain ALR surface.

For a 100 inch screen, the AWOL Vision ALR-F210C stands out with a 0.8 gain surface and a USB trigger that raises the screen when the projector powers on. The VIVIDSTORM S PRO lists the highest light rejection figure here at 97 percent. The Elite Screens ezCinema Tab-Tension is the only matte white screen in the group, and it is the right pick when the projector is a short throw model rather than an ultra short throw laser unit.

Product Type Best for Key spec Main limit
AWOL Vision ALR-F210C Motorized floor rising Living rooms with overhead light 100 inches, 0.8 gain, 170 degrees Works only with ultra short throw projectors
VIVIDSTORM S PRO VSDSTUST100H Motorized floor rising Bright rooms and laser TV setups 100 inches, 0.6 gain, 97 percent light rejection Heavy at 61.73 pounds gross weight
NothingProjector Black Series Motorized floor rising Large 120 inch home theater 120 inches, 0.6 gain, 170 degrees Works only with ultra short throw projectors
Screen Innovations Short Throw Lift STLT120 Motorized floor rising Wide seating and high end rooms 120 inches, 0.6 gain, 90 percent light rejection Needs a short throw or ultra short throw projector
Elite Screens ezCinema Tab-Tension FT100XWV Pull up tab tension Short throw projectors and travel 100 inches, 1.1 gain, 4:3 No light rejecting surface

How we selected

We picked screens only when the maker or listing page stated short throw or ultra short throw use, a portable form, and a tensioned flat surface. Each entry below comes from a product page that was opened and read, with size, gain, viewing angle, and weight taken from that page. Screens with no stated throw type were left out.

Portable form mattered as much as the surface. Every screen here either rises from a floor housing or pulls up from a case, so none of them needs a fixed wall mount or a ceiling mount. That is the point of a portable screen: it appears for a movie or a meeting, then folds away and frees the room.

Flatness mattered too. A short range projector throws light at a steep angle, so ripples and curls show up as bent lines and uneven brightness. That is why the list favors tab tension, wire tension, and scissor backed designs over loose hanging fabric. Gain, viewing angle, and stated light rejection were compared next, and size was kept in the 100 inch to 120 inch range that fits most living rooms.

Portable screens for short range projectors

The five screens below cover two kinds of short range setup: floor rising ALR screens for ultra short throw laser projectors, and one pull up screen for short throw projectors. All five fold away or roll down when not in use, so none needs a fixed wall mount. Read the throw type first, then size and gain.

AWOL Vision ALR-F210C 100 inch motorized floor rising screen

The AWOL Vision ALR-F210C is a 100 inch motorized floor rising screen built for ultra short throw projectors. It rolls up into a free standing base when not in use, so no wall mounting is needed. The maker lists a 0.8 gain HBSI ALR surface that rejects 95 percent of ceiling light.

This screen suits a living room where the projector sits on a low cabinet close to the wall and the ceiling lights stay on. The view area measures 87.2 inches wide by 49 inches high in a 16:9 shape, and the viewing angle is 170 degrees, so seats off to the side still get a clear image. The maker lists support for 4K and 8K resolution and active 3D, and the bottom of the screen uses sound transmitting material so speakers placed behind it stay audible.

Setup is simple for a motorized screen. The USB synchronized trigger connects to the projector, and the screen rises when the projector powers on and lowers when it powers off. The remote also adjusts height, which helps when the projector sits at a different height than planned. The item dimensions are 92.9 inches wide by 60 inches high, and the product weight is 52 pounds, so moving it between rooms takes two people or a cart.

The main limit is throw type. The maker states that the ALR-F210C is compatible with any ultra short throw laser projector and is not compatible with long throw projectors. A standard throw projector placed farther back will not match the optical surface, and the image will lose contrast. The listing shows a 120 inch option as well as the 100 inch model covered here, so buyers who need a larger image should look at that option rather than stretching this one.

  • Free standing base, so no wall mounting or drilling is needed
  • USB trigger syncs the screen with projector power
  • Remote height adjustment after the first setup
  • 170 degree viewing angle suits wide seating
  • Supports 4K and 8K resolution and active 3D
  • Works only with ultra short throw projectors
  • 52 pounds is heavy to carry far by hand
  • Needs power for the motor, so placement depends on an outlet

Buy if you own an ultra short throw laser projector and want a living room screen that hides away when not in use.

Skip if your projector is a standard throw or long throw model, or if you need a screen you can carry alone to another room.

VIVIDSTORM S PRO VSDSTUST100H 100 inch floor rising screen

The VIVIDSTORM S PRO VSDSTUST100H is a 100 inch motorized floor rising screen with an ultra short throw ALR surface. It rises from a floor housing and the listing describes a 30 second setup, with wire tension keeping the surface flat. The maker lists 0.6 gain and 97 percent light rejection.

This screen suits a bright room where a laser TV setup replaces a television. The view area measures 87.17 inches wide by 49.02 inches high in a 16:9 shape, and the viewing angle is 170 degrees. The maker lists support for 8K and 4K resolution and active 3D, and the screen comes with infrared and radio frequency remote controls. Sizes run from 72 inches to 120 inches, so the 100 inch model here is one of six sizes in the same line.

The housing is heavy duty aluminum in black or white, and the product dimensions are 98.43 inches wide by 8.27 inches high. The gross weight is 61.73 pounds, and the listed weight is 28 kg. A lock height adjustment lets the screen stop at a height that matches the projector, and a projector trigger dongle can sync the screen with the projector switch. The maker lists 110V power for this model.

The limits are weight and throw type. The maker states that the projector throw type is only compatible with ultra short throw laser projectors, and that the screen is not compatible with a ceiling mounted projector. The listing also recommends fastening the bottom bracket with screws, which makes the screen less of a grab and go item than a tripod screen. Buyers who move the screen often should weigh that step against the flat, tensioned image it gives.

  • 97 percent light rejection, the highest figure in this guide
  • Wire tension keeps the surface flat like glass, per the listing
  • Six sizes from 72 inches to 120 inches
  • Infrared and radio frequency remotes included
  • Lock height adjustment matches the screen to the projector
  • Works only with ultra short throw laser projectors
  • 61.73 pounds gross weight is heavy to move
  • Bottom bracket should be fastened with screws, per the listing

Buy if you run an ultra short throw laser projector in a bright room and want strong light rejection in a floor rising form.

Skip if your projector is ceiling mounted or standard throw, or if you need a screen that moves between rooms every day.

NothingProjector Black Series 120 inch motorized floor rising screen

The NothingProjector Black Series is a 120 inch motorized floor rising screen for ultra short throw projectors. It uses a Premium HBST PET surface with ST Carbon Black coating, 0.6 gain, and a 170 degree viewing angle. The maker lists 95 percent ambient light rejection and sizes from 84 to 130 inches.

This screen suits a home theater that wants the largest image in this guide without a fixed frame on the wall. The 120 inch model has a package weight of 33 kg, which the listing also gives as 72 lb. The bottom black border has a perforated acoustic aperture of 0.4 mm, so sound from speakers behind the lower part of the screen can pass through. The maker lists support for 3D, 4K, and 8K resolution, and the ratio is 16:9.

Control is flexible. The screen ships with a wireless radio frequency remote, a power cord, and a wireless projector trigger, and it works with Siri, Alexa, and Google Assistant voice control. The floor rising design rises at the press of a button and retracts into its housing when the show ends. A retractable flap at the bottom adds reinforcement, with an extended width of 8.5 inches and a retracted width of 6.3 inches.

The limits are throw type, weight, and height. The maker states that the screen is compatible with UST projectors only, and the maximum height has been preset at the factory, so it should not be adjusted beyond that limit. At 72 lb package weight for the 120 inch model, this is a two person move, and it needs floor space for a housing that is as wide as the screen itself.

  • 120 inch image, the largest size in this guide
  • Voice control with Siri, Alexa, and Google Assistant
  • Perforated acoustic bottom border of 0.4 mm
  • Wireless remote and projector trigger included
  • Sizes from 84 inches to 130 inches
  • Works only with ultra short throw projectors
  • 72 lb package weight for the 120 inch model
  • Maximum height is preset at the factory

Buy if you want a large 120 inch ultra short throw screen with voice control and a floor rising design for a living room theater.

Skip if your projector is not an ultra short throw model, or if you need a light screen that one person can carry.

Screen Innovations Short Throw Lift STLT120 120 inch floor rising screen

The Screen Innovations Short Throw Lift STLT120 is a 120 inch bottom up motorized ALR screen made for short throw and ultra short throw projectors. Its clamshell case hides the screen when it is down, and hidden handles help with moving it. The maker lists 0.6 gain and 90 percent ambient light rejection.

This screen suits a room where seating spreads wide and the projector sits below the screen. The view area measures 104.6 inches wide by 58.8 inches high in a 16:9 shape, and the maker lists a viewing angle of more than 140 degrees. CNC tab tension holds the surface flat, and the maker lists the surface material as rated up to 8K resolution, with 4K listed as the supported resolution. The minimum throw is 0.1 times the width, which fits projectors placed very close to the wall.

Control covers radio frequency, infrared, and a 12V trigger, plus button control, and the power source is 110V AC, with 220V AC listed for international use. The case color is black and the surface color is gray, and the mount type is floor. The listing shows the screen as in stock, and the included accessories are a charging cable, an infrared remote kit, and mounting brackets.

The limits are size range and gain. The maker lists 120 inches as the maximum size for this material, so buyers who want a smaller screen must look at a different line. The 0.6 gain surface returns less light than a 1.1 gain matte white surface, so a bright projector helps in a room with lights on. The ALR table on the listing also states that the material is not acoustic, so speakers should sit beside the screen rather than behind it.

  • Built for short throw and ultra short throw projectors
  • CNC tab tension keeps the image flat
  • Clamshell case hides the screen when down
  • Viewing angle of more than 140 degrees
  • Radio frequency, infrared, and 12V trigger control
  • 120 inches is the maximum size listed for this material
  • 0.6 gain returns less light than matte white
  • Material is not acoustic, per the listing

Buy if you own a short throw or ultra short throw projector and want a 120 inch floor rising screen that disappears into a clamshell case.

Skip if you need a smaller screen, or if your projector is a standard throw or long throw model.

Elite Screens ezCinema Tab-Tension FT100XWV 100 inch pull-up screen

The Elite Screens ezCinema Tab-Tension FT100XWV is a 100 inch pull up screen with a matte white surface and a 1.1 gain. Its tab tension design keeps the sides flat, which the maker links to short throw projector use. The scissor backed frame pulls up from its case with no tools.

This screen suits short throw projectors that sit a little farther back than ultra short throw laser units, and it suits travel and presentations. The aspect ratio is 4:3, and the listing gives the projection type as front projection, standard, and short throw. The matte white material has a wide viewing angle and is masked on all four sides, and the black backing blocks light from passing through the fabric.

At 42.6 pounds, this is the lightest screen in this guide by listed weight, and it is also the only one that needs no power. The free standing design pulls up and retracts with a scissor backed mechanism, and the maker describes it as a projector screen in a box for portable presentations on the go. The listing shows the screen as in stock and sold and shipped by Elite Screens Inc.

The limits are the surface and the shape. The listing states that ambient light rejecting is not a feature of this screen, so a bright room will wash out the image more than on the ALR models above. The 4:3 shape fits slides and older video well, but widescreen movies will leave unused bands at the top and bottom. Matte white also shows room light more than a gray ALR surface, so dimming the room helps.

  • Lightest listed weight here at 42.6 pounds
  • Works with short throw projectors, not only ultra short throw
  • 1.1 gain matte white surface
  • No power needed, and no tools for setup
  • Black backing blocks light penetration
  • No light rejecting surface, per the listing
  • 4:3 shape leaves bands with widescreen movies
  • Manual pull up setup takes more effort than a motor

Buy if your projector is a short throw model and you want a portable pull up screen that needs no power and travels light.

Skip if you own an ultra short throw laser projector, or if you watch mostly in a bright room with the lights on.

Buying guide

A screen that works well with a long throw projector can look poor with a short range model, because the light hits the surface at a steep angle. The points below help you match the screen material, size, and form to the projector you own, and to the room where it will sit.

Match the screen to short range projectors

Throw type is the first filter, and it is also the easiest to get wrong. Ultra short throw laser projectors need an ALR surface shaped to catch light from below, and the makers of the four floor rising screens here state ultra short throw use plainly. A short throw projector that sits farther back can use a tensioned matte white screen.

Read the compatibility line on the product page before anything else. If the maker states that a screen is not compatible with long throw projectors, take that at face value. If the maker states that a screen is for ultra short throw projectors only, do not plan to use it with a standard throw unit. The wrong pairing gives a dim image with poor contrast, and no setting on the projector fixes an optical mismatch.

Pick the right size for the room

Size starts with viewing distance and wall width. A 100 inch screen needs a wall about 87 inches wide for the image alone, plus room for the housing. A 120 inch screen needs about 105 inches of image width, so measure the wall before ordering. The 120 inch screens suit larger rooms, while the 100 inch models fit smaller rooms.

Height matters too. Floor rising screens rise from the floor, so the top of a 120 inch screen sits high on the wall, and the bottom sits near the floor. Check that the screen will not block a window, a shelf, or a speaker. Pull up screens can stop at a lower height, which helps when the ceiling is low or the seating is close.

Gain and viewing angle

Gain describes how much light the surface returns toward the viewer. A 1.1 gain matte white surface returns slightly more light than a plain white wall, while a 0.6 gain ALR surface returns less light but blocks far more room light. In a dark room, the higher gain screen looks brighter, while in a bright room the ALR surface keeps contrast.

Viewing angle describes how far off center the image stays clear. The floor rising ALR screens here list 170 degrees, and the Screen Innovations model lists more than 140 degrees. A wide angle matters when seats spread across the room. A narrow angle can look fine from the center seat and dull from the side, so match the angle to the seating layout.

Light rejecting material or matte white

Light rejecting material uses a shaped surface to catch projector light from below and turn away light from above. The four floor rising screens here use that idea, with stated light rejection from 90 percent to 97 percent. That design is what makes an ultra short throw projector usable in a living room with the lights on.

Matte white is simpler and cheaper to make, and it works with more throw types. The Elite pull up screen uses matte white with a 1.1 gain, and it suits short throw projectors in a room that can be dimmed. If the room has large windows and no curtains, the ALR models are the better pick. If the room can go dark, matte white gives a bright image at a lower cost and weight.

Weight, setup, and storage

Portable screens are heavy for their size. The listed weights here run from 42.6 pounds for the Elite pull up screen to 72 lb package weight for the 120 inch NothingProjector model, with the AWOL at 52 pounds and the VIVIDSTORM at 61.73 pounds gross. Housings run about 92 to 98 inches wide, so check doorways before moving one.

Setup differs by type. Motorized floor rising screens need power and a flat floor, and some need the bottom bracket fastened, while a pull up screen needs no power but takes manual effort. Storage differs too: a floor rising screen retracts into its housing and stays in the room, while a pull up screen folds into a case that can go into a closet or a car.

FAQ

Short range projectors raise the same questions again and again: which screens fit, how flat the surface must be, and what size works in a small room. The answers below use only the facts stated on the product pages in this guide, plus general buying points that apply to any screen.

Can a portable screen work with short range projectors

Yes, when the screen is made for the throw type. The four floor rising screens here are built for ultra short throw laser projectors, and the Elite pull up screen is listed for short throw use. A portable screen works when its surface is tensioned flat and its material matches the angle of the projector light.

The key is to match the screen to the projector, not to the room alone. A screen made for ultra short throw projectors will not suit a standard throw unit, and a plain matte white screen will not give the best contrast with an ultra short throw laser projector in a bright room. Read the compatibility line first, then look at size and gain.

What is the difference between short throw and ultra short throw

A short throw projector sits a short distance from the screen, often about a meter back for a 100 inch image, while an ultra short throw projector sits on a cabinet almost against the wall, just inches away. Both are short range projectors, but the light angle is very different, and the screen material must match that angle.

Ultra short throw projectors need an ALR or CLR surface with a shaped structure that catches light from below. Short throw projectors can use a tensioned matte white surface, because the light arrives at a less steep angle. That is why this guide splits the picks into four ALR floor rising screens and one matte white pull up screen.

Do floor rising screens need wall mounting

No. The four floor rising screens here use a free standing base or housing that sits on the floor, and the makers describe setup without wall mounting or drilling. The AWOL screen lists a sturdy free standing base, and the VIVIDSTORM screen plugs in and rises from the floor.

One note applies: the VIVIDSTORM listing recommends fastening the bottom bracket with screws to stop the screen from shaking. That is a stability step rather than a wall mount, but it does make the screen less portable. The other floor rising screens rise and retract with no fastening step stated on their pages.

How flat must a screen be for a short throw projector

Very flat. A short range projector throws light at a steep angle, so even a small ripple bends straight lines and creates uneven brightness across the image. That is why the screens here use tab tension, wire tension, or a scissor backed frame to hold the fabric tight.

When comparing screens, look for the tension method in the product description. Tab tension pulls the sides flat, wire tension pulls the surface from the housing, and a scissor backed frame holds a pull up screen rigid. A screen with no stated tension method is a risk with a short throw projector, even if the size and gain look right.

Which screen size suits a small room

A 100 inch screen suits most small rooms, with an image about 87 inches wide and 49 inches high in 16:9. The AWOL, VIVIDSTORM, and Elite models here are all 100 inch screens, and they fit a wall that is about 8 feet wide. A 120 inch screen needs about 105 inches of image width and suits a larger living room.

Viewing distance also sets the limit. Sit too close to a 120 inch screen and the image fills more of your view than is comfortable, while a 100 inch screen at the same distance feels calmer. If the room is under about 12 feet deep, start with the 100 inch size and check the wall width before ordering a larger model.

Conclusion

For short range setups, a floor rising ALR screen is the right pick with an ultra short throw laser projector, and the 120 inch NothingProjector and Screen Innovations models give the largest image. With a short throw model that sits farther back, the Elite pull up screen fits better. Match screen type to throw type, then pick size and gain.

Related guides

Browse all Buying Guides guides →